1)  ferritic electrodu
铁素体焊条
2)  iron element
铁素
3)  δ-ferrite
δ-铁素体
1.
The high δ-ferrite number(level)in 1Cr18Ni9Ti austenitic stainless steel is the main factor to affect its rolling(forging)billet surface quality.
1Cr18Ni9Ti奥氏体不锈钢中δ-铁素体数量(级)过高是影响其轧(锻)坯表面质量的主要因素。
2.
Control of δ-Ferrite Content in Precipitation Hardening Stainless Steel 17-4PH;
研究了17－4PH沉淀硬化不锈钢中δ－铁素体的形成因素、形态特征和化学成分配比，得出最佳成分（％）为：C0。
4)  δ-ferrite
δ铁素体
1.
Effect of δ-ferrite on impact properties of 12%Cr rotor steel for ultra-supercritical steam conditions;
δ铁素体对12%Cr超超临界转子钢冲击性能的影响
2.
The matrix of the powders was principally austenite;as the particle size decreased,the matrix changed from austenite to a composite consisting of austenite andδ-ferrite.
粉末基体组织以奥氏体为主,仅小粒径粉末基体由奥氏体与δ铁素体组成。
3.
The results obtained by SEM,EDAX,AES and metallographic analysis have showed that the surface films of the weld metals after sodium corrosion mainly consist of chromium carbides and NaCrO2, and corne off to form sodium corrosion pits in some area,the pattern of sodium corrosion is the pitting and preference solution of δ-ferrite, the mean corrosion depth of the met.
SEM,EDAX,AES和金相分析表明,钠蚀后焊缝表面膜主要由铬的碳化物、NaCrO_2组成,局部脱落形成钠蚀坑,钠蚀形态为点蚀和δ铁素体优先溶解,平均钠蚀深度为7。
5)  ferrite region
铁素体区
1.
Systematically investigated and discussed texture formation mechanism of IF steel sheet hot-rolled in ferrite region and its transformation mechanism during cold-rolling/annealing by means of the microstructure observation and crystallographic orientation distribution function(ODF).
通过金相观察和织构ODF分析,系统地研究了铁素体区热轧IF钢织构的形成机制及其在冷轧和退火过程中织构转变的特点和机理。
6)  ferrite
铁素体
1.
Mechanical behaviors of a low carbon steel with a duplex microstructure of bainite and ferrite;
铁素体和贝氏体复相组织低碳钢的力学特性
2.
Progress in Study on Precipitation Strengthening of Nb(C,N)in Ferrite of Niobium Microalloying HSLA Steel;
铌微合金化HSLA钢铁素体中Nb(C，N)析出强化的研究进展
3.
Analysis of Phase Transformation of Austenite-ferrite in Linear Thermal Expansion Measarement of Medium-Carbon-High-Alloy-High-Strength Steel;
中碳高合金高强度钢线膨胀测量中奥氏体-铁素体相变过程分析
参考词条
补充资料：低温铁素体钢
分子式：
CAS号：

性质：适合低温(273～153K)使用的低合金铁素体钢。它们在脆性转变温度以上使用。可为三类：(1)低碳-锰钢，如233K用钢16Mn属于此类；(2)低镍钢，在233～213K用0.5％Ni钢；当温度降至193～183K时，用2.25％Ni钢，或含锰的1.5％Ni钢；(3)无镍铬低温铁素体钢，主要有203K用钢09Mn2V及09MnTiCuRE，183K用钢06MnNb，153K用钢06AlCu和06AlNbCuN。低温铁素体钢主要用于液体丙烷与丙烯、液氨等液化气的储存及输送装置，寒冷地区野外作业的设备和工程结构以及一些冷冻设备等。

说明：补充资料仅用于学习参考，请勿用于其它任何用途。