1)  casing connections,casing joint
套管联接
2)  casing pipe
套管
1.
Early diagnosis for the stress concentration zone of borehole casing pipe by metal magnetic memory and wavelet transform;
磁记忆与小波变换相结合的井下套管应力集中早期诊断方法
2.
Study on collapsing strength of casing pipe on the residual stress;
套管的残余应力对抗挤毁强度的影响
3)  case
套管
1.
Monitoring technique and application of reservoir,case and wellsite facilities which oilfield development mainly concerns are introduced.
文章介绍了油气开发中主要关心的油气藏、井场设备及套管的监测技术和运用效果,油气藏监测主要是剩余油和油藏储藏物性的监测,套损直接影响油、水井的使用寿命、油、气产量和注水效果,井场设备运行的好坏直接关系油、气产量和注水效果,输油(注水)管道泄漏造成资源的浪费、人身伤害和环境污染事故。
2.
Accord to high water containing developing period of Daqing oilfield and actual situation of case damaged seriously in water and oil wells, a set of explosive perforation tech for cased well is introduced.
针对大庆油田开发进入高含水开采阶段,油水井套管损坏显著加快的实际情况,介绍了套损井爆炸打通道工艺技术。
3.
Injection unbalance caused by case damaged not only effects unsteady of oil field production, but also brings about oil-water well stopped, discarded which makes it unusually conduct of normal operation.
玉门油田在注水开发过程中,油水井套管损坏情况非常严重。
4)  sleeve
套管
1.
Punching technology for the sleeve of a new type expansion bolt;
膨胀螺栓套管冲压成形工艺
2.
Ultimate strength of sleeve reinforced T-joints under out-plane bending;
套管加强T型管节点在平面外弯矩作用下极限强度分析
3.
Various defects may occur in the production of plastic sleeve of railway switch tie with non-alkali glass fiber reinforced polyamide 66(GFRPA66), and reasons caused these defects are analyzed.
采用玻璃纤维增强尼龙66(GFRPA66)为原材料生产铁路岔枕套管时经常出现各种制品缺陷,分析了这些缺陷产生的原因,提出了通过调整成型工艺条件(注射温度、注塑压力、注射时间等)、改进模具结构及对原料进行预干燥处理等解决措施。
5)  bushing
套管
1.
Wetted Analysis and Preventive Measures of Bushing in Converter Transformer;
换流变压器套管受潮分析及预防措施
2.
Application and Discussion of Value Side Bushing Test Method of Converter Transformer in 500kV Converter Substation;
500kV换流站换流变阀侧套管试验方法的探讨及应用
3.
Partial Discharge Phenomena of Oil-Paper Capacitor Bushing and Their Analysis;
油纸电容式套管局部放电现象及分析
6)  casing
套管
1.
Research on Corrosion Mechanism of Casing Steel in Saturated Brine;
套管钢在饱和盐水中的腐蚀机理研究
2.
Influence of non-uniform external-pressure load on the load-bearing capacity of casing;
非均匀外载荷对套管承载能力的影响分析
3.
Stress analysis and strength study of hydraulic slotting casing;
水力割缝套管应力与强度分析
参考词条
补充资料:RGTGN套管杀菌机系列浓浆型

 

应用:
应用于浓缩果浆、果酱(如番茄酱、杏酱)等流体食品,物料在套管式热交换器中进行高温杀菌处理。

工作原理:
杀菌机是通过在高压下用循环热水30分钟来实现灭菌的,除菌后,系统逐步被降至生产温度,就可以进入生产阶段。
产品在经过前期处理后,进入杀菌机物料罐,输送泵将产品送入套管热交换单元进行预热。
最后在管式热交换器中进行加热,产品须在保温管中保温一定的要求时间以取得预定的杀菌效果。
产品在波纹管中利用热回收方式冷却至包装温度。
每个生产周期结束后,都要用碱液或酸对系统进行清洗。

设备组成及技术指标:
由物桶、套管式换热器、无级变速输送泵、高压柱塞泵、保持器、密闭水桶、热水发生器、控制柜等组成。
采用镜面焊接技术,保持管道连接平滑,减少物料残留。
采用波纹管连接,减少热变形应力。
杀菌不足自动返回管路,确保系统无菌性。
无菌阀,冷却管路连接法蓝采用蒸汽保护。
采用热回收技术,提高热传输效率,节约能源。
液位,温度实时控制。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。