1) flash weld tool joint
闪光焊钻杆
2) flash weld tool joint
闪光焊钻杆接头
3) welded drill pipe
对焊钻杆
1.
Development of heat treatment automatic control system for welded drill pipe;
对焊钻杆热处理自动控制系统研制
4) drill pipe welding
钻杆焊接
5) flash butt welding
闪光焊
1.
Control method of special flash butt welding machine in thin strip cold rolling steel plate;
冷轧薄钢板专用闪光焊机控制方法
2.
Study on the technology of AMS60 movable AC flash butt welding machine;
AMS60钢轨交流闪光焊机焊接工艺研究
3.
Research on domestic monitored control system for К900 rail flash butt welding machine;
K900钢轨闪光焊焊机计算机监控软件国产化研究
6) flash welding
闪光焊接
1.
The welding of billets was simulated on UN 100 preheat flash welding machine for 20MnSi steel, the rolling experments was performed on φ300 mill, then the hardness and structure of the welded joint after deformation was studied.
研究了棒线材无头轧制的工艺参数 ,选择 2 0 Mn Si钢作为研究对象 ,采用预热闪光焊接模拟高温状态下的坯料焊接。
2.
The weld is required to have similar properties as the matrix of the bar and wire produced by endless rolling process The welding of 20MnSi steel was simulated with UN 100 preheat flash welding machine,the rolling experiments was carried out on φ300 mill,the influence of elongation coefficient on the structure,plasticity and toughness of the weld was studied.
以 2 0 Mn Si钢为研究对象 ,采用预热闪光焊接模拟高温状态下的坯料焊接 ,焊后轧制使用 30 0轧机。
3.
The 20MnSi steel blank high temperature welding was simulated by UN-100 preheat flash welding machine for the rolling was performed on φ 300 mill, then the influence of upset force on the structure, plasticity and toughness of the welded area was studied.
本文以 2 0 Mn Si钢作为研究对象 ,焊接实验用 UN- 10 0型闪光焊机 ,采用预热闪光焊接模拟高温状态下的坯料焊接 ,轧制用 30 0轧机。
补充资料：闪光对焊
闪光对焊
flash butt welding
shanguang dulhan闪光对焊(flash butt welding)一种压焊方法。焊件装配成对接接头，并夹在通电的夹具上，使焊件端面缓缓地移近到局部接触，利用产生的电阻热使接触点很快被加热至高温，形成闪光或电弧，同时产生强烈的金属飞溅，继续移近焊件直至整个端面在一定深度范围内达到预定温度时，则迅速施加顶锻力完成焊接。闪光对焊又可分为连续闪光焊和预热闪光焊。特点闪光对焊接合面上的熔融金属层在顶锻时被挤出，起了清除接合面上杂质的作用，对接合面的准备要求不严。各种截面的环形零件都可以焊接，其接头的热影响区比电阻对焊窄得多。闪光焊的接头飞边和顶锻金属需要专门设备去除。被焊的两个零件必须具有差不多相同的截面。 应用可焊接黑色金属和有色金属，如低碳钢和低合金钢，不锈钢，铝、镍、铜、钦及其合金，以及异种金属如铝与铜、镍和钢等。 (率忠玉)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条