1) Mechanical wheel wear
砂轮机械磨损
2) grinding wheel wear
砂轮磨损
1.
The Influence of Grinding Wheel Wear on Transmission Properties of Quasi-Plane Double Enveloping Hourglass Worm Gearing;
砂轮磨损对准平面二次包络环面蜗杆传动性能的影响
2.
Comparison was made on the grinding parameters including grinding ratio(G-ratio) and grinding wheel wear.
通过分别采用国产陶瓷结合剂CBN砂轮与刚玉砂轮对45淬硬钢工件进行磨削试验,对磨削过程中的参数:磨削比和砂轮磨损进行对比。
3.
According to the grinding experiment, the Kullback-Leibler information distance method is used to recognize grinding wheel wear states in the grinding process by means of the signal processing to grinding sparks.
通过磨削试验 ,应用KL信息距离法对磨削火花信号进行处理以识别磨削过程中砂轮磨损状态的变化。
3) mechanical grinding by diamond wheel
金刚石砂轮机械刃磨
1.
Two kinds of popular grinding technologies for polycrystalline diamond (PCD) cutters--the electrical discharge grinding (EDG) and the mechanical grinding by diamond wheel are introduced.
介绍了聚晶金刚石 (PCD)刀具的两种常用刃磨方法———放电刃磨和金刚石砂轮机械刃磨的刃磨机理、刃磨设备及研究成果 ,并针对两种刃磨方法的不足提出了今后的研究方向。
4) mechanical wear
机械磨损
1.
The results show that the friction coefficient and wear loss of the brushes due to electrical wear are higher than those due to mechanical wear.
研究了以上3种复合材料电刷在相同的压力和线速度条件下的机械磨损性能和电磨损性能。
2.
The results show that the wear volume loss of composites increases with the increase of pressure under mechanical wear,but the wear volume loss of composites varies with the change of pressure by U shape under electrical wear.
研究了压力变化对碳纳米管银石墨复合材料纯机械磨损和电磨损性能的影响。
3.
These factors main have mechanical wear and corrosion wear.
主要有机械磨损和腐蚀磨损。
5) physical attrition
机械磨损(碎)
6) grinder
[英]['ɡraɪndə(r)] [美]['graɪndɚ]
磨床砂轮机
补充资料：机械类常用英语：砂轮用语
abrasive 砂轮 Al2O3 氧化铝
balance 平衡 bond 结合
borazon 氧化硼立方晶 buffing wheel 抛光布轮
diamond 钻石 dresser 砂轮整修机
dressing 修整 endless grinding belt 循环式研磨带
finishing allowance 加工余量 grain 磨粒
grinding disc 研磨盘 jamp up 孔眼堵塞
mesh 网筛目 parameter 参数
resinoid grinding wheel 半树脂型砂轮 slitting 切缝量
vitrified 陶瓷的 wheel 旋转
balance 平衡 bond 结合
borazon 氧化硼立方晶 buffing wheel 抛光布轮
diamond 钻石 dresser 砂轮整修机
dressing 修整 endless grinding belt 循环式研磨带
finishing allowance 加工余量 grain 磨粒
grinding disc 研磨盘 jamp up 孔眼堵塞
mesh 网筛目 parameter 参数
resinoid grinding wheel 半树脂型砂轮 slitting 切缝量
vitrified 陶瓷的 wheel 旋转
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条