1) sharp edge notch tensile strength
锐角切口拉伸强度(冶)
2) notched tensile specimen
切口拉伸试样<冶>
3) sharp edgenotched sheet
锐角切口薄板试样(冶)
4) tensile shear strength
拉伸剪切强度
1.
MTS-810 testing apparatus and scanning electron microscope were used to study the tensile shear strength, elongation and microstructure of epoxy construction adhesive before and after the vacuum thermal cycling.
采用MTS-810型材料试验机和扫描电子显微镜,研究了真空热循环下环氧结构胶粘剂拉伸剪切强度、延伸率和微观结构等变化规律。
2.
In this paper,the influences of curing agent,low molecular polyamide,organophilic montmorillonite and nano-Al2O3 on tensile shear strength and erosion and wear resistance of epoxy resin coating were studied,the results showed that the tensile shear strength and the erosion and wear resistance of the coating can be improved obviously with organophilic montmorillonite and nano-Al2O3.
研究了固化剂低分子聚酰胺、有机蒙脱土和纳米Al2O3的用量对环氧树脂胶粘涂层拉伸剪切强度和耐冲蚀磨损性能的影响。
5) tensile strength
拉伸剪切强度
1.
Polyurethane adhesives prepared from liquefied wood has the tensile strength of 5 MPa,which meets the application requirement.
利用液化产物制备了聚氨酯胶黏剂,拉伸剪切强度达5 MPa,达到应用要求,为今后的工业化生产提供了依据。
2.
The influence of the ratio of monomers and photoinitiator on tensile strength was discussed.
本研究采用三种丙烯酸酯单体(M01、M02、M03)和一种紫外光引发剂(I01)配制了紫外光固化胶粘剂,探讨了不同原料配比对产品拉伸剪切强度的影响。
3.
The data of adhesion and tensile strength showed that the water-based CPP paint can substitute for solvent-based CPP coating.
从粘附力和拉伸剪切强度测定结果可以看出,用水性氯化聚丙烯代替溶剂型氯化聚丙烯是可行的。
6) tensile shearing strength
拉伸剪切强度
1.
The effect on the tensile shearing strength of the ratio of polyether polyol to epoxy resin,the ratio of A component to B component and the surface treatment process were studied.
考查了聚醚多元醇与环氧树脂的配比,A与B组分配比及表面处理工艺对拉伸剪切强度的影响。
2.
The tensile shearing strength of anodic and cathodic epoxy electrophoretic coatings and spray epoxy painting on aluminium alloy and steel were determined according to national standard of tensile shearing strength determination method for adhesives.
借鉴国标胶粘剂拉伸剪切强度测定方法测定了阳极、阴极环氧电泳漆与环氧涂料在底材为铝合金及钢材上漆膜的拉伸剪切强度。
补充资料：干态拉伸强度
分子式：
CAS号：
性质：又称干态拉伸强度。在规定条件下，以胶黏剂胶接成的制件在干燥后或试片经状态调节后，立即测得的胶接强度。利用测量胶黏剂的干强度可以提供出胶黏剂是否符合标准要求，而且在实际应用时，该指标更能反映出被黏制件经黏结后能否达到使用要求。
CAS号：
性质：又称干态拉伸强度。在规定条件下，以胶黏剂胶接成的制件在干燥后或试片经状态调节后，立即测得的胶接强度。利用测量胶黏剂的干强度可以提供出胶黏剂是否符合标准要求，而且在实际应用时，该指标更能反映出被黏制件经黏结后能否达到使用要求。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条