1) hot test loop
热态试验回路
2) hot test loop
放射性试验回路;(反应堆)热试验回路
4) thermal test
热态试验
1.
The campaign of blast furnace is prolonged by using copper staves, and the thermal performance of the staves is determined by thermal test and numerical simulation.
通过热态试验和数值模拟的方法来测试其热态性能。
2.
The thermal test system of cooling stave was designed and established to put up the industrial experiment of the heat transfer for the cast steel cooling stave and ductile iron cooling stave.
设计并建造了冷却壁热态试验系统,对铸钢冷却壁和球墨铸铁冷却壁的换热效果进行了工业模拟试验。
3.
The strain of cold surface and temperature of the stave under high thermal load were measured through thermal test,and the fields of temperature,strain and stress were also calculated through numerical simulation.
通过热态试验测量了高温下冷却壁的温度分布和冷面应变分布,通过数值模拟计算了冷却壁的温度场和应力应变场。
5) hot state test
热态试验
1.
Therefore,hot state tests were carried out,on an internally circulating fluidized bed test rig,using coal as fuel.
因此,在1个内循环流化床燃烧试验台上进行了以煤为燃料的热态试验。
6) hot test
热态试验
1.
The hot test of the copper cooling stave with circular channels was done in the test furnace designed by the authors.
在自行研制的热态试验炉上对圆孔型铜冷却壁进行了热模拟试验。
2.
Simulating the operation conditions of staves of No3 BF at Baosteel,the first experimental furnace in China for hot test of large stave has been establishedThe influence of temperature and velocity of inlet water,gas temperature of BF and heat impact on the temperature distribution of the stave have been studiedThe main cause of stave damage is discusse
模拟宝钢３号高炉冷却壁的实际工作条件，建立了国内第一台大型冷却壁热态试验炉。
3.
The contrast hot test of the copper cooling stave with different cooling channels was done in the hot test whole-scale furnace which is designed by the authors.
在自行设计的1:1热态试验炉上对不同孔型的铜冷却壁进行了热态对比试验,对试验结果作了传热学分析,提出优化铜冷却壁水流通道断面设计的方法,优化后的水流通道可以达到强化传热和减少铜料消耗以及节约冷却水用量的目的。
补充资料：堆内试验回路
分子式：
CAS号：
性质：在试验反应堆内试验新材料和考验其他反应堆元件时，为了接近实际，常在反应堆内设置一个专门回路进行实验。该回路的冷却剂自成循环，它在堆外联有专门的小型回路。该试验回路与试验堆不发生任何直接联系，即使被考验元件损坏，也不会沾污试验堆。试验回路内的热量也不会散到试验堆中去，这样既可完成试验任务，又保证试验堆参数不变。
CAS号：
性质：在试验反应堆内试验新材料和考验其他反应堆元件时，为了接近实际，常在反应堆内设置一个专门回路进行实验。该回路的冷却剂自成循环，它在堆外联有专门的小型回路。该试验回路与试验堆不发生任何直接联系，即使被考验元件损坏，也不会沾污试验堆。试验回路内的热量也不会散到试验堆中去，这样既可完成试验任务，又保证试验堆参数不变。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条