1) section depth
切面高度
2) burnish length
剪切面高度
1.
Aiming at increasing the burnish length of blanked workpiece,a new assumption on dual positive clearance blanking for thick plate is proposed,based on summing up various existing shearing processes of blanking.
为提高普通冲裁件断面中剪切面高度,在总结现有各种冲压分离工艺方法的基础上,提出了一种新的厚板冲裁构想,其模具结构设计为:阶梯型冲头或阶梯形凹模,且为双重正间隙。
2.
Under the previous manufacturing conditions,blanking experiments were carried out and was obtained advancement The burnish length in the cross-section of big hole was more than half of material thickness,which was twice over the original .
在原加工条件下,进行了多次冲裁试验,获得的轮辐大孔断面剪切面高度大于料厚一半,达到原剪切面高度的两倍,并进行了相关分析。
4) slice depth
切削高度
1.
This paper studies in detail the dropping cut method which the Bucket Wheel Excavator normally adopts,and on this basis,deduces carefully some more exact formulas of slice depth,width and height in dropping cutting process.
本文针对斗轮挖掘机经常采用的水平切削方式作了较为详细的分析,在此基础上推导了水平切割时切削厚度、切削高度和切削宽度的较为精确的计算公式,为斗轮挖掘机水平切削时的受力分析和功率计算提供了较为可靠的理论依据。
5) punching shear depth
冲切高度
6) cutting height
切口高度
1.
Based on mechanics principles, this paper calculates the cutting height and cutting angle of tubular building directional demolition.
根据力学原理 ,计算了钢筋混凝土筒形结构定向倾倒拆除的切口高度和切口角度 ,分析了筒形结构的定向倾倒过程。
2.
The cutting height and cutting angle of directional dernoiltion of tubularbuilding are analysed and calculated according to mechanics principles.
根据力学原理,分析讨论了钢筋混凝土筒式结构定向倾倒的切口高度和切口角度。
补充资料:安东刀切面
[原料/调料]
- 面条﹕面粉3杯﹐豆粉1杯
- 调料﹕鸡800g﹐鸡蛋2个﹐辣椒丝 少量﹐紫菜2张
- 肉佐料﹕盐少量﹐切好的葱2小勺﹐捣好的蒜1小勺﹐胡椒面少量﹐香油1/2大勺﹐芝麻2小勺
- 汤﹕煮鸡的汤
[制作流程]
(1) 把面粉和豆粉混在一起和面﹐并做刀切面放在开水里煮熟。
(2)等煮鸡的汤凉后﹐撩去油并调味。
(3)鸡蛋煎成黄﹑白鸡蛋切成丝。
(4)紫菜切小。
(5)把面条盛在碗里倒鸡汤后放煎鸡蛋﹑辣椒丝﹑切好的紫菜﹑拌的鸡肉。
(6)配佐料一起吃。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。