1) vapor-oil -water separator
汽-油-水分离器
2) gasoline trap
汽油分离器
3) steam-water separator
汽水分离器
1.
Aiming at the difficulties of radiographic detection to girth weld of steam-water separator which has no manhole or detectionhole in power plant.
针对无人孔和探伤孔的电站汽水分离器封头环焊缝射线探伤的难点,通过理论计算和实际对比分析、制定出适合的检测工艺,实践证明工艺满足国家相关标准的要求。
2.
The numerical simulation and experimental research of steam-water separator with cor- rugated plate is carried out in this paper.
本文对波形板汽水分离器进行了数值模拟和试验研究。
4) steam separator
汽水分离器
1.
On the primary and secondary steam separator with a water defector in a steam generator for PWR;
PWR蒸汽发生器中一、二次汽水分离器加装挡水器研究
2.
Analysis is carryied out with 3-dimension FEM for super critical boiler’s thick-wall parts stress fields by inside pressure,the steam separator’s stress concentrating factor is calculated.
采用三维有限元计算对超临界锅炉厚壁部件在内压作用下的应力场进行了分析,并计算出汽水分离器应力集中系数。
3.
The paper takes the steam separator of 600MW supercritical boiler as subject investigated, and builds a 3D computation module, with the finite element method, we calculate the temperature field, thermal stress field, mechanical stress field and the whole stress field of the steam separator in the process of cold start-up, analyses the law change in temperature field and stress field.
汽水分离器是超临界锅炉中最重要的厚壁部件。
5) steam/water separator
汽水分离器
1.
This paper first makes a theoretical analysis of the stress field of steam/water separator, an important pressure-bearing p.
本文首先对超临界锅炉中重要的承压部件—汽水分离器的应力场进行了理论分析,并进一步分析了在运行过程中产生疲劳蠕变损伤的机理。
6) steam water separator
汽水分离器
1.
During viscous crude oil steam flooding,a high pressure steam water separator is introduced to improve steam quality and then enhance recovery factor.
为在稠油热采蒸汽驱阶段提高注汽干度 ,进而提高稠油开采率 ,引进了高压汽水分离器 。
补充资料：皂化溶解油、肥皂油和调水油
分子式：
CAS号：
性质：又称皂化溶解油、肥皂油和调水油。金属切削油的一类。一般是淡褐色至深褐以液体或半固体。由在矿物油中加入适量的皂类乳化剂（如钠皂、钾皂、松香钠皂、松香皂或环烷酸钠皂）和少量稳定剂（如乙醇或甲醇）而成。使用时与软水掺合成稳定的白色乳化液。作用以冷却为主，润滑为次。用于车制、锯断、钻孔、磨制等金属粗加工。
CAS号：
性质：又称皂化溶解油、肥皂油和调水油。金属切削油的一类。一般是淡褐色至深褐以液体或半固体。由在矿物油中加入适量的皂类乳化剂（如钠皂、钾皂、松香钠皂、松香皂或环烷酸钠皂）和少量稳定剂（如乙醇或甲醇）而成。使用时与软水掺合成稳定的白色乳化液。作用以冷却为主，润滑为次。用于车制、锯断、钻孔、磨制等金属粗加工。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条