1) windage loss
![点击朗读](/dictall/images/read.gif)
气流损失
2) corner loss
![点击朗读](/dictall/images/read.gif)
转弯损失(气流)
3) air convection loss
![点击朗读](/dictall/images/read.gif)
空气对流损失
4) air heater draft losses
![点击朗读](/dictall/images/read.gif)
空气加热流动损失
5) lost gas
![点击朗读](/dictall/images/read.gif)
损失气
1.
Simulation experiment and result analysis on lost gas content of coalbed methane
![点击朗读](/dictall/images/read.gif)
煤层气损失气含量模拟试验及结果分析
6) aerodynamic loss
![点击朗读](/dictall/images/read.gif)
气动损失
1.
The effects on turbine blade surface pressure and aerodynamic loss distribution ofcoolantanair inject from each of three individual rows of coolant holes on the blade leading-edge, and the rear of the suction and the pressure surface were investigated in a Iinearcascade.
本文通过实验研究了冷气喷射对叶型型面压力和叶栅流道内气动损失的影响,并得出了一些有意义的结论。
2.
But this carried much aerodynamic loss.
![点击朗读](/dictall/images/read.gif)
燃气涡轮叶片是涡轮发动机中热应力最大、承受温度最高的部件,涡轮进口燃气温度远高于涡轮叶片材料的耐热极限,因此需要大量的冷气给叶片散热和形成冷气膜,但是大量冷气的使用带来极大的气动损失。
3.
Various factors influencing the air-film cooling effectiveness and their effects on the aerodynamic losses were expounded.
介绍了气膜冷却的基本原理,总结了叶片端壁、顶部、前缘及尾缘区域气膜冷却的研究进展和气膜孔流量系数的研究状况,阐述了影响气膜冷却效果的各种因素及气膜冷却对气动损失的影响。
补充资料:DWP喷射气流干燥机
![](/picture/bkimg/ch_7/7_22_181_0.jpg)
工作原理:
DWP型属喷射气流带式干燥类型,热风以狭缝流或孔束流向下或上下同时喷向输送带上的物料,由于喷射气带高达15m/s以上,故对流传热的传热膜极薄,传热系数大,干燥速度快。该设备用于不透气类物料时,上面喷射气流仍返回上面,下面喷出的气体仍返出下面,再参与循环。对透气性物料如涂膜布干燥等,也适用于片状物料及一些特殊物料的干燥。如果采用双向气流喷射,板材之类物料干燥后变形小。喷射气流干燥使用热源可以是蒸气、电、热风炉及燃油烟道气等。
应用范围:
喷射气流带式干燥专用设备,比如纸浆干燥一般为S型或M形结构的多层式,大型纸浆模则为单层式。前者输送为吊蓝型,后者为为网带输送型。并且热风温度、循环气体量、湿度、气流速度及气流束形式不为其它物料所通用,实际差别很大。
对用户的咨询,我厂工程师会迅速作出详细的合理的设计方案,愿与用户一道,促使我们的设备性能更好,效益更好。
![](/picture/bkimg/ch_7/7_22_181_1.jpg)
技术参数:
名称\参数\序号 | DWP-Ⅰ | DWP-Ⅱ | DWP-Ⅲ | |
带宽m | 1.6 | |||
干燥段长m | 8 | |||
铺料厚mm | 10-80 | |||
使用温度oC | 50-120 | |||
蒸汽压力Mpa | 0.2-0.6 | |||
换热面积m2 | 330 | 296 | 259 | |
干燥时间h | 0.2-1.2 | |||
风机数量 | 3 | 2 | 2 | |
传动机功率Kw | 0.75 | |||
风机功率 KW | 7.5*3*2 | 7.5 3 | 7.5 3 | |
外形尺寸 | 10*2.1*3.6 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条