1) eccentric lift table
偏心举升台
2) scissor-type lift table
剪式举升台
3) lifting platform
升降平台;举重台
4) eccentric gas lift valve
偏心气举阀
5) lifting
[英][lift] [美][lɪft]
举升
1.
But in the production process,the scaling of lifting system can lead to the pump stucking,the rod parting increasing and the pump inspection interval shorting,which has affected the production percentage and oil displacement effect seriously.
三元复合驱具有驱油效果好、采收率高的优点,但在生产过程中,由于举升系统结垢造成油井卡泵、杆断现象多,检泵周期短,严重影响了油井的生产时率和驱油效果。
2.
As for the current problems existed in the lifting technology in Lu Kewin oilfield, the study on rheological characteristic and viscosity-temperature characteristics of heavy oil was conducted.
针对鲁克沁油田目前举升工艺存在的问题,通过对稠油流变性和粘温性的研究,确定采用潜油电泵举升技术开采,产量大幅度提高。
6) lift
[英][lɪft] [美][lɪft]
举升
1.
With the application of PCS intelligence plunger lift technique,the gas wells renew their production without any additional power.
在深入调查研究的基础上 ,开展了将油井上应用较为成熟的 PCS智能柱塞举升技术引入这些气井上的试验。
2.
There often exist dangers when a tipper is lifting body or riding.
本文针对自卸车在车箱举升与行车方面易产生危险事故,设计一控线路以解决该问题。
3.
The corresponding measure was produced according to characteristic of heavy dump truck that length is larger,and it has certain directive function for design of lifting system of heavy dump truck.
通过对J5P自卸车的简要设计分析,针对长度较大的重型自卸车的特点,从举升系统的结构设计及液压设计方面提出了相应的措施,对重型自卸车的举升系统设计有一定参考作用。
补充资料：在AutoCAD中偏心圆锥与偏心圆台实体的画法
现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上.
1)连接PA,PB. A(-100,0,0) B(100,0,0)
图1
在当前坐标下:
2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;
3)连接CD;
4)以CD为直径画圆;
5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;
6)过O作CD的垂线,交圆于E,F;
图2
7)用三点UCS命令,取三点为:O,P,C;
8)过点O作PO的垂线GO,交PC于G;
图3
9)再次用三点UCS命令,取三点为O,F,G;
10)现在就可以画椭圆锥了!
cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;
图4
11)回到WCS,剖切椭圆锥
SL-选择椭圆锥-回车-XY-回车-捕捉P点.
12)删除辅助线条.
图5
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条