1) flap valve,plate valve
片状阀
2) plate-like
片状
1.
The effects of plate-like alumina seed amount on the microstructure and properties of alumina ceramics prepared by pressureless sintering were studied,when plate-like alumina single crystal particles were used as seeds and CaO-Al2O3-SiO2(CAS) were used as additives.
以片状氧化铝单晶颗粒为晶种,CaO-Al2O3-SiO2(CAS)为添加剂,采用无压烧结研究了晶种加入量对氧化铝陶瓷显微结构与性能的影响。
2.
A process for the preparation of different particles of CaC03 is intruducted, the effect of various factors on CaCO3 crystal is discussed and spherical and plate-like calcium carbonate with small partical size are obstained.
采用溶液法制备了不同晶形碳酸钙,讨论了各种因素对碳酸钙结晶的影响,并得到了粒径较小的球状和片状碳酸钙。
3.
The effects of plate-like alumina seed additions on the microstructure and properties of alumina ceramics were studied, when plate-like alumina single crystal particles were used as seeds and CaO-Al2O3-SiO2(CAS) were used as additives.
本文以片状氧化铝单晶颗粒为晶种,CaO-Al2O3-SiO2(CAS)为添加剂,研究了晶种加入对氧化铝陶瓷显微结构与性能的影响。
3) Flake
片状
1.
The ultrafine flake copper particles with diameter from 1 μm to 10μm were prepared by using chemical reduction method with ascorbic acid as reducing agent.
采用液相化学还原法,以抗坏血酸为还原剂,NH3·H2O、乙二胺或EDTA为络合剂,制备了1～10μm表面光滑的片状超细铜粉。
4) platelike
片状
1.
Preparation of platelike CaCO_3 by emulsion method;
乳液法制备片状CaCO_3
2.
The influence factors on the formation of platelike crystalline α-Al2O3 powders were investigated by XRD and SEM.
本研究以工业氢氧化铝粉体为原料,加入矿化剂和晶种, 通过高温固相反应制备出分敌均匀的片状α-Al2O3粉体。
5) flake-like
片状
1.
Based on the principles of biomineralization,nano flake-like hydroxyapatite(HA) were synthesized through biomimetic method using Ca(NO3)2·4H2O and(NH4)3PO4·3H2O as reagents and chondroitin sulfate as template.
依据生物矿化的原理,以硫酸软骨素(ChS)为模板合成了片状纳米羟基磷灰石(HA)。
6) sheet-like morphology
片状形貌
参考词条
补充资料：溢流阀、顺序阀、减压阀的比较
溢流阀 | 减压阀 | 顺序阀 | ||
控制油路的特点 | 通过调整弹簧的压力控制进油路的压力，保证进口压力恒定，p2＝0 | 通过调整弹簧的压力控制出油口的压力，保证出口压力p2稳定 | 直控式－通过调定调压弹簧的压力控制进油路压力；夜控式－由单独油路控制压力 | |
出油口情况 | 出油口与油箱相连 | 出油口与减压回路相连 | 出油口与工作回路相连 | |
泄漏形式 | 内泄式 | 外泄式 | 内泄式 | |
进油口状态及压力值 | 常态 | 常闭（原始状态） | 常开（原始状态） | 常闭（原始状态） |
工作状态 | 进出油口相通，进油口压力为调整压力 | 进油口压力低于出油口压力，出油口压力稳定在调定值上 | 进出油口相通，进油口压力允许继续升高 | |
联接方式 | 并联 | 串联 | 实现顺序动作式串联作卸荷阀用时并联 | |
功用 | 定压、溢流或安全作用限压、稳压、保压 | 减压、稳压 | 不控制系统的压力，只利用系统的压力变化控制油路的通断 | |
进油腔压力p1控制阀芯移动 | 出油腔压力p2控制阀芯移动 | 进油腔压力p1控制阀芯移动 | ||
说明：补充资料仅用于学习参考，请勿用于其它任何用途。