说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 离子橡胶
1)  ionic rubber
离子橡胶
2)  E-SBR with ionic crosslinking bond
离子交联乳聚丁苯橡胶
1.
Synthesis and properties of E-SBR with ionic crosslinking bond;
离子交联乳聚丁苯橡胶的合成与性能
3)  rubber particle
橡胶粒子
1.
A rubber particle protein with apparent molecular mass of 43 kD as determined by SDS-PAGE was purified.
对43 kD的橡胶粒子膜蛋白进行了分离纯化和其N端氨基酸序列分析,根据N端氨基酸序列,设计一简并引物,通过3’RACE(Rapid Amplification ofcDNA Ends)的方法,获得了43 kD的橡胶粒子膜蛋白的cDNA。
2.
The rubber molecules inside rubber particles are the primary inclusions of natural rubber.
橡胶粒子是橡胶树乳管细胞质中进行橡胶生物合成的一种特殊细胞器,其内部的主要成分橡胶烃分子,是天然橡胶的直接来源。
3.
A rubber particle is enclosed by semi-unit biomembrane.
橡胶粒子是由半单位生物膜包裹的细胞器,表面带负电荷,能够吸附水分子;由于在细胞中橡胶粒子数量极多,故能形成较强束缚水分的能力。
4)  stator rubber
定子橡胶
1.
Influence of stator rubber plumping of screw pumps on volume efficiency and countermeasures;
螺杆泵定子橡胶溶胀对容积效率的影响及对策
2.
The stator of the general single progressive cavity pump is studied in this paper,using finite element analyzing software,at 5 MPa uniformity pressure of the stator,which concluded the stress,the strain and inner-figure deformation of the progressive cavity pump stator,the stator rubber and the stator steel thimble.
利用ANSTYS有限元分析软件对常规单螺杆泵的定子进行研究,在定子承受5 MPa均匀压力作用下,得出了定子、定子橡胶和定子钢套的应力、应变和内轮廓的变形量;分析了常规单螺杆泵定子变形的特点及规律。
3.
Among the problems of rod string, broken is the most severest problem, and among the problems of pump, leakage that mainly due to the damages of the stator rubber and broken of the rotor takes the largest proportion.
在杆柱问题中,杆断问题最严重,而在泵问题中,泵漏失占的比例最大,主要是定子橡胶损坏和转子断脱。
5)  rubber stator
橡胶定子
1.
Study on the rubber stator compoundof one step injection screw drilling tool;
一步法注射螺杆钻具橡胶定子胶料的研制
2.
he paper presents a test method to research the dynamic property of the rubber stator for screw pump,compares the result of static and dynamic tests and selects the formulation according to the tests.
提出研究螺杆泵定子橡胶动态性能的试验方法,对静态试验及动态试验结果进行对比,并应用其试验对配方进行筛选,结果表明,橡胶压缩温升试验能较好地表征螺杆泵定子橡胶的动态性能,为橡胶定子的研究提供了较为可靠的依据,并在实际应用中得以证实。
3.
Conventional progressing cavity pumps consist of two elements:the rubber stator and the metallic rotor.
常规单螺杆泵包含两个主要的部件即橡胶定子和金属转子,定子与转子之间的相互作用是影响螺杆泵性能的主要因素之一。
6)  rubber particles
橡胶粒子
1.
Properties of cement mortar incorporating rubber particles-PVA fiber;
橡胶粒子-PVA纤维复合改性水泥砂浆的性能研究
2.
In order to improve the shrinkage cracking of cement-base material,the cement mortar incorporating rubber particles and PVA fiber were investigated.
针对水泥基材料收缩裂缝问题,进行了利用橡胶粒子与PVA纤维复合改善水泥砂浆抗裂性的试验研究,并对橡胶粒子与PVA纤维在水泥砂浆中的阻裂机理进行了初步探讨。
3.
There is more obvious optimizing effect on the impact strength,anti-crack property and toughness of cement concrete when the additive composition of scrap tire rubber particles replaces a part of mineral aggregate in cement concrete,and a large number of scrap tires are comsumed,which have an important benefit to the recycling utilization of scrap tires and environmental protection.
在水泥混凝土中掺加废旧轮胎橡胶粒子取代部分矿物集料可改善混凝土的抗冲击、抗裂性能和增加韧性,并可消耗大量的废旧轮胎,具有资源循环利用和环保意义。
补充资料:橡胶模具、橡胶压模、橡胶硫化模
分子式:
CAS号:

性质:又称橡胶模具、橡胶压模、橡胶硫化模。用于压制橡胶产品的金属模型。一般用钢材(如45号钢)按图纸要求经机械加工而制得,并经热处理以提高其硬度及耐磨性。模具型腔与产品结构相同,型腔尺寸必须考虑不同橡胶的收缩率,在产品尺寸基础上进行放大或缩小,方可得到合适的产品尺寸。模具从工艺操作考虑还要设置流胶槽、启模口、定位销等。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条