1) build up of dielectric strength
绝缘强度的恢复
2) insulation recovery
绝缘恢复
1.
This paper presents results obtained during experiment research on the insulation recovery of the rep-rate gas spark gap.
在自行设计的气体火花开关上，利用双脉冲回路，对纳秒脉冲作用下Ｎ２和Ｈ２的绝缘恢复特性进行了实验研究。
3) Dielectric recovery
绝缘恢复
1.
To find the ways to increase repetition rates and lifetime of the switches, mechanisms of two physical processes which determine repetition rates and lifetime of the switches ,dielectric recovery and electrode erosion, were studied in theory, and a serial of high-energy high-coulomb repetitive experiments were performed with two different three-electrode gas spark switches designed by ours.
为了探寻提高开关重复频率和寿命的技术途径和方法，对制约开关重复频率和寿命的两个主要物理过程—绝缘恢复和电极烧蚀的机理进行了理论研究。
4) self restoring insulation
自恢复绝缘
1.
Therefore it raises the intensity of self restoring insulation and enhances the ability of cutting out short circuit current in circuit breaker.
这个方法可以限制短路电流过零点的增长速度，因而可以提高自恢复绝缘强度，增强断路器切断短路电流的能力，计算结果与测试一致。
5) dielectric strength
绝缘强度
1.
Analysis dielectric strength of new type SF_6 circuit breaker after current zero;
SF_6新型断路器的弧后介质绝缘强度的分析
2.
The dielectric strength E b and corrosion resistance properties of ceramic coatings formed by micro-arc oxidation(MAO) on MB8 magnesium alloys were studied by breakdown test and salt spray test, respectively.
采用微弧氧化法在MB8镁合金表面原位生长一层陶瓷层,利用电击穿试验、盐雾腐蚀试验等手段研究了陶瓷层的绝缘强度Eb 和耐蚀性,并用扫描电镜(SEM)分析了陶瓷层的形貌结构。
3.
The dielectric strength of transformer oils decreases when it is stored for long time due to the unperfect process flow in the transformer oils unit.
变压器油生产装置由于工艺流程不完善,导致产品在长时间储存时绝缘强度下降,提出变压器油生产合理、可行的后处理流程为闪蒸-吸附组合工艺,从而提高变压器油绝缘强度,解决了产品不能长时间储存的问题。
6) insulation strength
绝缘强度
1.
In view of the problems of instauration of insulation strength of the transformer after installation,this paper introduces some suitable methods and attention points for recovering insulation strength of the transformer on the construction spot,from the aspects of taking vacuum,oil handling,pouring oil with vacuum,and oil supplying.
针对变压器安装后的绝缘强度恢复问题,从抽真空、油处理、真空注油、补油几方面介绍了一些适合于施工现场的恢复变压器绝缘强度的措施和注意事项。
补充资料：高强度绝缘漆
分子式：
分子量：
CAS号：
性质：耐热指数130或130以上的绝缘漆。主要用于漆包线，如聚酯酰亚胺、聚酰亚胺和聚酰胺亚胺等绝缘漆。见漆包线漆。
分子量：
CAS号：
性质：耐热指数130或130以上的绝缘漆。主要用于漆包线，如聚酯酰亚胺、聚酰亚胺和聚酰胺亚胺等绝缘漆。见漆包线漆。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条