1) angular aberration
角度橡差
2) Angle error
角度误差
1.
The angle errors between the sight of target and the optical axial of a laser seeker characterizing the interactional effect, al.
用所记录的目标视线和系统光轴角误差数据表征相互作用效应,说明高重频激光压制干扰与激光制导系统相互作用效应表现为激光导引头的信息处理机制被破坏,不能正常给出的水平、俯仰角度误差信息,但这种破坏在压制干扰消除后即刻消除。
2.
In order to simplify the calculation,we often intentionally neglect the angle error and assume the angle variable to be constant,which will adversely affect the precision of the solution.
应用全微分概念,不忽略角度误差的影响,解平面尺寸链,概念清晰,计算准确,分析了角度误差在平面尺寸链中的作用。
3.
It is concluded that the angle error has no impact on the detection results and the profile errors of the two refraction surfaces have little effect,but the profile errors of the two reflection surfaces have great influence on the detection.
分析了五棱镜加工的角度误差及面形误差对检测结果的影响,得出了五棱镜角度误差不影响检测结果,2个折射面的面形误差对检测结果的影响较小,2个反射面的面形误差对检测结果影响最大的结论。
3) angle deviation
角度偏差
1.
Through comparing the image of the sample with the stand- ard one,the angle deviation and position deviation was obtained.
通过对摄取到的实际套准标记图像和标准图像进行比较,输出其角度偏差值和位置偏差值,以此作为自动套准控制系统中时印刷机套准调节的依据,并对一种"米"形套准标记的识别和检测进行了分析。
2.
The model with angle deviation was detail discussed, correct model could be made by exactly angle measurement.
分析了基于球杆仪的数控机床误差补偿测试原理 ,讨论了由于角度偏差引起的误差 ,指出基于球杆仪误差补偿模型的缺陷 ,提出采用该种模型必须精确测量角度
3.
Through comparing the image of the sample with the stand- ard one,the angle deviation and position deviation was obtained.
通过对摄取到的实际套准标记图像和标准图像进行比较,输出其角度偏差值和位置偏差值,以此作为自动套准控制系统中对印刷机套准调节的依据,并对一种"(?)"形套准标记的识别和检测进行了分析。
4) angle difference
角度差
1.
Conclusion is made for the range of teeth highness,front angle,teeth density for varied capacity and varied production in clothing collocation,as well as the range of rate of the teeth highness,angle difference,teeth density.
从针布齿条的总高、前角、齿密等方面分析了国外针布配套的基本思想,归纳出不同产量和不同品种针布配套中总高、前角、齿密的范围及配套针布间的总高比、角度差、齿密比的范围;提出了在针布配套中要考虑针布使用寿命的设想,并对此进行了论证;为针布生产及配套提供借鉴和参考。
2.
The radar imaging angle differences of the corresponding locations on the original orbit and its ROIOs are also proposed in this paper.
针对运载火箭二级助推器及分离时产生的大的碎片对雷达观测可能造成的影响,阐述了雷达成像重叠轨道(ROIO)的概念,并就雷达处于火箭载荷轨道平面内的情况分析了ROIO的存在条件、确定方法和观测中火箭载荷轨道及其ROIO上所对应的位置相对于雷达的角度差。
5) angular error
角度误差
1.
The analyse of theary about effect on angular error for reflective characterisitic of move angular cone prism;
角度误差影响运动角锥棱镜反射特性的理论分析
2.
The more exact temperature is measured,the more accurate angular error could be compensated.
温度漂移是陀螺角度误差的主要误差源之一,严重影响了陀螺的测量精度,因此需要对陀螺角度输出误差进行补偿。
3.
The straightness and angular error of a machine guide are main factors to assure high quality of mechanical components in the precise manufacturing.
在精密机械加工行业中导轨直线度和角度误差是影响加工工件质量的重要因素,传统的干涉方法检测过程烦琐而漫长,研制一种能同时测量导轨多自由度误差的仪器具有较大的应用前景。
6) angle windage
角度偏差
1.
The effect of angle windage on the linking intensity of interference fits;
角度偏差对过盈联接强度的影响
2.
On the basis of analyzing the pressure change aroused by angle windage on linking length, this thesis presents a math model of circle moment for interference fits in the dissimilarity of generatrix angle, then states the effects opposite circle moment because of angle windage, thus, to provide reference for the design of taper interference fit
本文在分析母线角度编差引起配合长度上压力变化的基础上,提出了在母线角度不同时计算圆锥过盈连接圆周力矩的数学模型,论述了母线角度偏差对相对圆周力矩的影响,为圆锥过盈联接的设计提供了重要的理论参考依据。
补充资料：差差
1.犹参差。不齐貌。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条