1) latex coating
胶乳涂布
2) latex(treated) paper
乳胶涂布加工纸
3) latex coatings
乳胶涂料
1.
Architectural latex coatings are prepared with the suspension.
以氧化铝纤维毡经剪切、分散、除杂及改性后,制得稳定的含氧化铝纤维悬浮液的建筑乳胶涂料,经性能测试涂层硬度,耐沾污性和耐擦洗性等有很大提高,涂料体系的触变性、储存稳定性也有明显改善。
2.
On the base of analyzing the major source of VOC in latex coatings, the ways that are used to eliminate VOC are introduced in two sides of preparing emulsions and selecting additives.
在分析乳胶涂料中VOC主要来源的基础上,从乳液合成和助剂选择两方面阐述了消除VOC的途径。
3.
This article introduces the preparation of nano-meterTiO2 light catalyzed latex coatings through the reaction ofnano-meter TiO2 with other compositions.
采用纳米TiO2作为主要组分,通过其与其他组分之间相互作用而制得纳米TiO2光触媒乳胶涂料,通过检测其一系列性能(普通性能和光触媒净化性能),由此得出纳米TiO2光触媒乳胶涂料具有环保优良特性的结论。
4) latex paint
乳胶涂料
1.
The change of nature of paintfilm in which was added is measured,and the influnce of nano-CaCO_3 on nature of latex paint is revealed.
介绍了纳米CaCO_3结构,测定了加入纳米CaCO_3后涂料及其涂膜的性能的变化,揭示了纳米CaCO_3对乳胶涂料性能的影响。
2.
Waterborns have been experiencing technological growth for the past 30 years, latex paint especially the exterior paint is very popular at present since the environmental concern were highlighted.
涂料水性化技术在过去的三十年里得到了迅速的发展，由于对环境法规的日益重视，乳胶涂料特别是外墙乳胶涂料获得了广泛的应用。
5) latex coating
乳胶涂料
1.
Synthesis and preparation of low VOC acrylate emulsion and latex coating;
低VOC纯丙乳液及乳胶涂料的合成与配制
6) emulsion paint
乳胶涂料
1.
In this paper, the structure of Kaolin was analyzed, the properties of coatings and its films were examined, and the ef-fects of Kaolin to the emulsion paint were also discussed.
本文分析了高岭土的结构、测定了加入高岭土后涂料及其涂膜的性能的变化,揭示了高岭土对乳胶涂料性能的影响。
2.
Several commercialized low surface energy auxiliary agent such as LD ultra hydrophobic nano interface agent,Zonyl fluorin surface active agent series,SILRES BS1306、BYK-Silclean 3700 are selected in the design of paint formula and its influence on dirt resistance of emulsion paint for external wall is studied.
在涂料配方设计中选择LD超疏水性纳米界面剂、Zonyl氟表面活性剂系列、SILRES BS1306、BYK-Silclean 3700等几种商品化的低表面能助剂,研究其对外墙乳胶涂料耐沾污性的影响。
补充资料：凹印辊涂布机
分子式：
CAS号：
性质：全称辊式涂布机。即用一组以上的回转辊筒把一定量的涂料涂布到平面状材料上的装置。改变两辊之间的压力，可调节涂布的厚度。典型的辊涂机有辊舐涂布机，压辊涂布机(凹印辊涂布机)，正、反辊式涂布机等。此外用小直径涂布辊代替涂布刮刀的涂布机亦称辊涂机。
CAS号：
性质：全称辊式涂布机。即用一组以上的回转辊筒把一定量的涂料涂布到平面状材料上的装置。改变两辊之间的压力，可调节涂布的厚度。典型的辊涂机有辊舐涂布机，压辊涂布机(凹印辊涂布机)，正、反辊式涂布机等。此外用小直径涂布辊代替涂布刮刀的涂布机亦称辊涂机。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条