1) roller bearing
滚棒轴承
2) roller bearing without inner race
无内圈滚棒轴承
3) taper(ed) (conical) roller bearing
锥形滚棒轴承
4) ball bearing
滚动轴承
1.
Nonlinear dynamic response analysis of unbalance-rubbing coupling faults of rotor-ball bearing-stator coupling system;
转子-滚动轴承-机匣耦合系统的不平衡-碰摩耦合故障非线性动力学响应分析
2.
Model for dynamic characteristics produced by inner race local defect in ball bearing system and its simulation;
内圈局部损伤滚动轴承系统动态特性建模及仿真
3.
Extraction of the Fault Features of Ball Bearings Based on Bispectrum Analysis;
基于双谱分析的滚动轴承故障特征提取
5) needle roller bearing
滚针轴承
1.
In order to eliminate the defects of needle roller bearing cage after gas soft nitriding,tempering is performed at 180~300 ℃,based on early experiments of austenitic area soft nitriding.
为了消除08钢制滚针轴承保持架气体软氮化(ANCT)后存在组织分布不均匀、性能达不到要求等缺陷,在前期奥氏体区软氮化工艺试验的基础上,选择180~300℃回火温度进行回火处理。
2.
In this paper, the effects of chamfer dimension at the roller end and the grinding undercut of raceway on the longitudinal pressure distribution of the needle rollers with Lundberg s profile, which are used in the needle roller bearings with machined guide rib.
结果表明,使用这种方法设计的滚针轴承,其接触压力分布不会出现"边缘效应",也不会在接触的中心部分出现应力集中。
3.
The damage case of general needle roller bearings has been analyzed emphatically after the new type of environmental protection coolant has been adopted in the air donditioner compressor.
着重分析空调压缩机采用新的环保型冷媒体后 ,常规结构滚针轴承的破坏情况 ,提出了冲压滚针轴承新的结构改进设计及其开发和性能比较结果 ,为今后新冷媒体空调压缩机的广泛使用 ,提供了有利的保
6) roller bearing
滚动轴承
1.
Analysis of load characteristic of roller bearing on work roll for an Aluminum foil mill;
铝箔轧机工作辊滚动轴承负荷特性分析
2.
Analyse on the Damage of Mill Roller Bearing and Its Prevention;
压榨机滚动轴承失效原因分析及其改进措施
3.
Morphology filters for analyzing roller bearing fault using acoustic emission signal processing;
形态滤波在滚动轴承故障声发射信号处理中的应用
补充资料：滚针轴承
用滚针作滚动体的滚动轴承（见图）。滚动体长度与直径之比大于 2.5的圆柱称为滚针。滚针轴承主要用于径向尺寸受限制而载荷又很大的地方，如汽车的连杆轴承、 活塞销轴承、 万向联轴节铰链轴承和变速器轴承等。但这类轴承摩擦力矩较大，不能承受轴向载荷。图为滚针轴承的主要结构型式。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条