1) recessed joint
方凹槽
2) groove
[英][ɡru:v] [美][gruv]
凹槽
1.
The Fast Multipole Method for Electromagnetic Scattering of a Groove in a Perfectly Conducting Plane;
无限大导体平面上凹槽散射的快速多极子分析
2.
Fast Calculation of Wide Angle Scattering Fields of a Groove in a Perfectly Conducting Plane Based on Asymptotic Waveform Evaluation Technique;
渐近波形估计应用于无限大导体平面上凹槽散射场宽角度方向性函数的快速获取
3.
BST thick films are fabricated in the grooved silicon substrate by tape casting method.
采用流延法在有凹槽的硅片上制备出钛酸锶钡((Ba,Sr)TiO3)厚膜材料。
3) cavity
[英]['kævəti] [美]['kævətɪ]
凹槽
1.
Numerical study of supersonic turbulence flows on 2-D cavity;
二维凹槽超声速湍流流动数值模拟
2.
Study on cavity flow characteristics of supersonic combustor;
超音速燃烧室凹槽流动特性研究
3.
The large eddy simulation of supersonic cavity flow field
超声速凹槽大涡数值模拟研究
4) notch groove
凹槽
1.
Experimental study on permeability of fresh-old concrete bonding interface with notch groove;
带凹槽的新老混凝土粘结面渗透性能试验研究
2.
Based on the bonding mechanism and permeability of repair interfacial layer between new and old concrete,an idea to significantly increase bonding impermeability by means of chipping notch groove on the old concrete was proposed.
通过带凹槽的老混凝土粘结面与新混凝土粘结的复合圆台柱体试件的渗透性能对比试验研究,分析了凹槽宽度、粗糙度、界面剂等对粘结面渗透性能的影响。
5) slot
[英][slɔt] [美][slɑt]
凹槽
1.
Vortex flow and cavitation inception in a slot;
凹槽中的旋涡及初生空化数的估算
2.
Impact the dimensions of slots on backscatter of the rotationally symmetric conducting targets;
凹槽的尺寸对旋转对称金属目标的后向RCS的影响
3.
The Finite-Difference Time Domain(FDTD)algorithms of anisotropic material was used to analyze the plan wave scattering by slots on aircraft loaded with anisotropic material.
利用各向异性时域有限差分法 (FDTD)分析填充不同介质凹槽的金属目标的电磁散射。
6) flute
[英][flu:t] [美][flut]
凹槽
1.
In combined pile group composite foundation indoor model experiment,the characteristics of both traditional inside and outside paste methods is analyzed,and a flute method is proposed and adopted,and its typical test results are presented in this paper.
在组合群桩复合地基室内模型试验中,本文结合传统内贴法和外贴法两种贴片方式的优点,提出并采用凹槽法在低强度实心模型桩外侧面贴片,即在桩侧预留凹槽、用环氧树脂对贴片部位进行表层处理,在贴片后密封凹槽,并给出了典型测试结果。
2.
In this article, the invalidation of the ektexine of the impeller was analyzed, and basing on this a new type of impeller with flutes was designed.
在分析了机械进丸抛丸器中分丸轮外壁失效的基础上设计出了一种新型的平行窗口带凹槽的分丸轮,降低了分丸轮外壁与弹丸的摩擦能量损耗,提高了机械进丸抛丸器的抛丸率和抛丸量。
补充资料：凹模壁厚及凹模垫板尺寸
型腔壁部投影面积 壁 厚， 毫 米
F， 厘米2 h1 h2 h3 h4 h5
<5 15~20 30~40 <=10 15~20 30~40
>5~10 20~25 40~50 10~15 20~25 40~55
>10~50 20~30 50~60 15~20 20~30 55~65
>50~100 30~35 60~75 20~25 30~40 65~70
>100~200 35~40 75~85 25~30 40~50 70~75
>200 >40 >85 30~35 50~60 >80
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条