1)  electric pig iron
电炉生铁
2)  EAF
电炉
1.
Discussion on Converting Process of EAF;
电炉转炉化生产工艺初探
2.
Practice of 20G Tube Blank Steel Produced by 100t EAF;
100t电炉生产20G工艺实践
3.
Optimized Configuration of Alloy-Steel Bar Production Using EAF Process;
合金钢棒材电炉生产流程的优化配置
3)  furnace
电炉
1.
According to study of ramming material characteristic,high matrix ramming material of high carbon ferrochrome furnace bottom can be made by means of using fine material as aggregate,calcined magnesia with MgO＞97% and size＜0.
088 mm烧结镁砂做细粉,适当添加超微粉等工艺措施,制成适当高碳铬铁电炉炉底用的高基质打结料,通过调控基质成分,实现材料相和固相的复合烧结。
2.
5 MVA ferroilicon furnace modular electrode holder which is designed by Sinosteel Jilin Electro-Mechanical Equipment Co.
5MVA硅铁电炉组合把持器的特点及应用情况。
3.
Better results have been achieved on the two units of ferroeilico-aluminium furnaces(5.
6MVA两台硅铝合金电炉联用除尘系统,并采用负压除尘,在运行中取得了良好的效果。
4)  electric stove
电炉
1.
The design of temperature control system of electric stove based on single chip microcomputer;
基于单片机的电炉温度控制系统设计
2.
In view of the serious chimney pollution of the 3 t electric stove and the harm to the staff health,the paper proposes that collecting chimney by dust cage at the top and the bag-type duster is the design scheme of chimney collecting purification processing.
文昌针对机修车间3 t电炉烟尘污染严重及危害职工身体健康情况,提出了顶部集烟罩捕集烟尘+袋式除尘器为烟尘捕集净化处理的设计方案。
3.
In this paper,we discuss the design about automatic control system of electric stove.
讨论了电炉自动控制系统的设计。
5)  electric arc furnace
电炉
1.
General layout design of 90t conseel electric arc furnace at shaogang;
韶钢90 t CONSTEEL电炉总图设计
2.
The dephosphorization technics has been studied on high-content phosphor RE concentrate in electric arc furnace.
通过对高磷稀土精矿电炉除磷工艺试验,探索了稀土精矿除磷工艺的最佳工艺条件,并取得了满意的效果。
6)  electric furnace
电炉
1.
Automatic constant power control system for No.2 electric furnace in Yunnan Copper;
云铜2~#电炉恒功率自动控制系统
2.
Installation of Spare Switches in a Large Electric Furnace to Increase Economic Efficiency;
大型电炉安装备用开关增加经济效益
3.
The Development and Present Situation of the Modern Electric Furnace Making Steel at Home and Abroad;
国内外电炉设备的现状与发展
参考词条
补充资料：NZ514生铁断裂机操作规程
1、遵守铸造设备通用操作规程。
2、逐个操纵各个伐门，检查管路系统是否漏气，如有漏气情况，应通知维修人员修理。
3、启动电动机，检查电动机，减速器及园盘的运动是否正常，确认一切正常后，方可进行生产。
4、工作时，注意安全，严防铁块飞出伤人。
5、工作后，锤头必须下落，推杆必须复位。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。