1) bulb turbine, bulb tubular type turbine
灯泡式(贯流)水轮机
2) tubular bulb unit
灯泡半贯流式水轮机
1.
The installation quality of main axis and axis bearing is the key for the installation of tubular bulb unit,the parallel degree,mileage,elevation of main axis must be strictly controlled by standard.
在灯泡半贯流式水轮机组中,主轴和轴承的安装质量好坏至关重要,主轴轴线的平行度、里程、高程必须严格控制在规范要求范围内,轴承中的轴瓦间隙直接影响到轴承冷却油温进而影响到机组运行的安全稳定。
3) Bulb turbine
灯泡贯流式水轮机
1.
Numerical method based on internal character for load rejection transient calculation of a bulb turbine installation;
灯泡贯流式水轮机装置甩负荷过渡过程基于内特性解析理论的数值计算方法
2.
The design of the shaft seal for the Bulb turbine occupy the very important station in the design of the turbine.
灯泡贯流式水轮机的主轴密封设计在灯泡贯流式水轮机的设计中占有极其重要的地位,本文简要介绍了一种新开发的浮动环式主轴密封的设计原理、典型结构及安装方式。
3.
The reliability of bulb turbine is low because of its structure and its working seal of main shaft is easy to happen accident.
灯泡贯流式水轮机受其结构形式的影响,机组安全可靠性低,主轴工作密封容易发生事故,如何提高机组主轴工作密封的可靠性对电站的安全运行有着非常重要的意义。
4) bulb tubular turbine
灯泡贯流式水轮机
1.
This paper presents the design process and structural characteristics of the runner and other parts of the bulb tubular turbine this the author s analysis for reference.
本文介绍了该电站灯泡贯流式水轮机转轮及其它各部件的设计过程和结构特点,以供同行参考。
5) flow-bulb hydrogenerator
灯泡贯流式水轮发电机
1.
Numerical simulation of flow field on ventilation system of flow-bulb hydrogenerator;
灯泡贯流式水轮发电机通风系统流场的数值模拟
2.
Numcrical Simulation of Flow Field on Ventilation System of Flow-bulb Hydrogenerator;
灯泡贯流式水轮发电机通风冷却系统的数值计算及模拟
3.
Numerical Simulation of Ventilation and Heat Dispersion for the Flow-bulb Hydrogenerator;
灯泡贯流式水轮发电机通风散热系统数值模拟
6) bulb hydrogenerator
灯泡贯流式水轮发电机
1.
The main structure of bulb hydrogenerator of Jiangkou power station is described in this paper.
介绍了江口电站灯泡贯流式水轮发电机的主要结构，以及关于通风、冷却、支承等技术问题的处理方法。
补充资料：贯流式水轮机
贯流式水轮机
tubular turbine;straflo turbine
水头3m;水头最高的是百龙滩水电站的灯泡贯流式机组，最大水头18m，额定水头9.7m，最小水头3m，水轮机额定功率33MW，转轮直径6.4m;转轮直径最大的是大源渡水电站的灯泡贯流式机组，转轮直径7.sm，水轮机额定功率30.%MW，最大水头n.24m，额定水头7.Zm，最小水头3m。gUon4IUshl shLJ一IL一{111贯流式水轮机(tubular turbine;straflo tur-bine)过流通道呈直线(或S形)布置的轴流式水轮机。其引水室及尾水管与水轮机一般为卧轴布置。使用水头范围一般为3~25m。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条