1) knotextensibility
打结伸长率
2) elogation
伸长，伸长率
3) elongation
[英][,i:lɔŋ'geiʃən] [美][ɪ,lɔŋ'geʃən]
伸长(延伸)率
4) elongation
[英][,i:lɔŋ'geiʃən] [美][ɪ,lɔŋ'geʃən]
伸长率
1.
Effect of rolling technology on elongation of two-side stainless steel cladding aluminum composite;
轧制工艺对双面不锈钢复铝板伸长率的影响
2.
The Cause for Low Elongation of Ductile Iron Pipein Hot Mold by Centrifugal Casting;
热模法离心铸造球铁管伸长率低的原因探析
3.
Study on some problems of elongation control in flat rolling;
冷轧平整机轧制伸长率控制问题研究
5) Percentage elongation
伸长率
1.
And the result that the properties of the Al-Si alloy were improved is obvious: the tensile strength and the percentage elongation within the scope certainly of the RE element content increased synchronously with the increase of RE content, and .
结果表明:该合金的抗拉强度和伸长率在一定浓度范围随RE含量增加而同步增长,且都有相同的最佳效果加入量,但稀土元素对铝硅合金的抗拉强度改善效果不是很明显。
2.
The reasons of low percentage elongation of mid Si Mo vermicular graphite cast iron exhaust tube casting in trial production were analyzed.
对试生产的中硅钼合金蠕墨铸铁排气管铸件本体伸长率不足的原因进行了显微组织分析。
3.
Besed on the study of a series of experiments,this article found the relationship of material percentage elongation and specimen gauge length.
基于试验研究,提出了材料伸长率与试样标距长度之间的经验关系,经对板式、棒式和管式试样的试验结果分析,利用定量关系换算的值与试验值吻合性很好。
6) elongation ratio
伸长率
1.
The stranded wire is used widely in civil engineering, its elongation ratio is one of important indexes, How to test precisely the index is a problem that has been researched for a long time.
钢绞线在土木工程中应用十分广泛,钢绞线的伸长率是钢绞线的重要力学性能指标之一,如何精确测量该指标是长期以来一直在探索的问题。
2.
Abnormal fracture of step appearance has been found during cold bending and stretching tests were conducted on hot rolled steel plate of 510L automobile crossbeam steel,and the elongation ratio was much lower than the standard value.
510L汽车大梁钢热轧钢板在进行冷弯、拉伸试验时,发现断口异常,呈台阶状,伸长率远低于标准要求。
补充资料：扯断伸长率
分子式：
CAS号：
性质：橡胶经硫化后，其原有的线型高分子结构被交联成网状结构，分子间作用力增大，具有一定的强度，能承受一定的作用力，将橡胶试样在拉力机上以一定速度拉断时，以试样拉伸前断面积上所承受的力(MPa)来表示拉伸强度。当橡胶试样拉断时，其伸长部分与原长度之比谓之扯断伸长率，以百分率(％)表示。
CAS号：
性质：橡胶经硫化后，其原有的线型高分子结构被交联成网状结构，分子间作用力增大，具有一定的强度，能承受一定的作用力，将橡胶试样在拉力机上以一定速度拉断时，以试样拉伸前断面积上所承受的力(MPa)来表示拉伸强度。当橡胶试样拉断时，其伸长部分与原长度之比谓之扯断伸长率，以百分率(％)表示。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条