1) mold clearing temperature
出模温度
2) extrusion temperature
挤出温度
1.
The influences of screw configuration,screw speed,extrusion temperature and water contents on extruded starch foams were studied.
研究了螺杆组合、螺杆转速、挤出温度以及含水量对淀粉挤出发泡的影响。
2.
The excellent properties of resin and fiber would be fully embodied through the proper propessing technique and conditions, extrusion temperature, extrusion rate, injection speed are the important factors influencing material property.
结果表明,适宜的加工工艺和加工条件能够将ABS和玻璃纤维本身的优良性能充分表现出来,挤出温度、挤出速度及注射速率都是影响材料性能的重要因素。
3.
The effect of main screw parameters (length/ diameter ratio, helix angle, channel depth and compression ratio)of cold feed rubber extruder on extrusion temperature were investigated by orthogonal regression method on the basis of the statistical analysis of experimental results.
研究了螺杆造型（长径比，螺旋升角，螺槽深度，螺杆几何压缩比），挤出工艺（螺杆转速，机头口型）和胶料种类对橡胶冷喂料挤出机挤出温度的影响，并对各实验因素及实验结果做了统计分析，得出了他们之间的定量数学模型。
3) Outlet temperature
出口温度
1.
The result shows that the outlet temperature by partial charged method is more steady and its discharging rate is higher than that by fully charged method.
比较了两种冻结方式在蓄冷和释冷过程中的传热性能,结果表明,不完全冻结方式在释冷过程中盘管出口温度更稳定、释冷速率更高,给出了不完全冻结必须满足的条件。
2.
On the basis of on-site data and in conjunction with the working principle of a power plant coal-pulverizer system a state-space dynamic mathematical model has been set up of the coal pulverizer outlet temperature and pulverizer inlet-air flow rate through an analysis of the coal pulverizer control system.
基于现场数据 ,结合电厂磨煤机系统的工作原理 ,通过对其控制系统分析 ,建立了磨煤机出口温度和磨煤机入口空气流量的状态空间动态数学模型。
3.
Two calculation methods for combustor outlet temperature of an aeroengine were described.
概要介绍了某型航空发动机燃烧室出口温度的2种计算方法,结合发动机试车数据对采用2种计算方法得到的结果进行了对比分析。
4) tower exit temperature
出塔温度
1.
This article discusses the influence of urea prilling tower exit temperature on the water percentage of urea,analyses the factors influencing urea prilling tower exit temperature,and puts forowrd suggestions to control the tower exit temperature through replacing the prilling sprayer and adjusting the shutter opening of prilling tower according to atmosphere temperature and humidity.
讨论尿素造粒出塔温度对尿素含水率的影响 ,对影响尿素造粒出塔温度的因素进行分析 ,提出通过更换喷头及根据环境温度和空气相对湿度调节百叶窗开度来控制尿素造粒出塔温
5) tapping temperature
出钢温度
1.
The measures adopted to reduce the content of oxygen in steel are introduced, such as catching carbon, raising rate of one-time turning down, lowering tapping temperature, controlling slag amount, white refining slag deoxidizing and etc.
介绍了石钢转炉厂为降低钢中氧含量采取的一系列措施,如高拉碳、提高一次倒炉率、降低出钢温度、控制下渣量、精炼白渣脱氧等,氧含量由2001年的50。
2.
By perfecting and optimizing converter maintenance technique, extending and utilizing new technology and new process of continuous casting, using new technique of reducing tapping temperature of converter, the reliable steel-making producing is guaranteed in the steel-making plant of Laigang, the campaign life of converter is increased to 30 thousand heats, the yield of billet is up to 99.
莱钢炼钢厂通过完善与优化转炉护炉技术、推广应用连铸新技术和新工艺、应用降低转炉出钢温度的新技术,保证了炼钢生产的稳定,转炉炉龄增至30000炉,连铸坯收得率达99。
6) leaching temperature
溶出温度
补充资料：石油产品馏出温度
分子式：
CAS号：
性质：石油产品在规定条件下进行馏程测定中，量筒内回收的冷凝液达到某一规定体积（ml）时观察到的温度。馏出体积为10ml时观察到的温度即称为10%（因为试样为100ml）馏出温度，简称10%点。馏出温度可以用来表示油品的馏分组成及使用性能。如汽油的初馏点、10%点、50%点及90%点以及终馏点可以用来分别说明汽油在发动机中的起动性能、加速性能、动力性能及蒸发完全的程度。
CAS号：
性质：石油产品在规定条件下进行馏程测定中，量筒内回收的冷凝液达到某一规定体积（ml）时观察到的温度。馏出体积为10ml时观察到的温度即称为10%（因为试样为100ml）馏出温度，简称10%点。馏出温度可以用来表示油品的馏分组成及使用性能。如汽油的初馏点、10%点、50%点及90%点以及终馏点可以用来分别说明汽油在发动机中的起动性能、加速性能、动力性能及蒸发完全的程度。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条