1) interpass temperature
程间温度
2) thermal history
温度随时间变化历程，温度时间关系
3) interpass temperature
层间温度
1.
Preheat and interpass temperature were determined,the welding material was choosen,the relevant process parameters,the welding procedure and the heat-treatment procedure were worked-out.
研究了T91与10CrMo910钢的异质焊接工艺,确定出预热和层间温度,选择了焊接材料,制订出相应的工艺参数和焊接、热处理工艺。
2.
The influence of welding heat input and interpass temperature on the impact value of the welded joint -30℃temperature are analyzed.
分别就焊接线能量、层间温度变化对焊接接头的-30℃冲击韧性的影响进行了试验,并用光学显微镜和电子显微镜观察了接头组织。
3.
In this paper,it adopts process actions,such as preheating,controlling heat input and interpass temperature,post-heat and slow cooling and it makes use of relative detecting method to impect the guality in low temperature welding.
通过采取焊前预热、控制焊接线能量和层间温度、焊后保温缓冷等工艺措施,并采用相应的检测方法,保证了胺液吸收塔的低温焊接质量。
4) interlayer temperature
层间温度
1.
According to the test,the welding interlayer temperature of X60 pipeline in the normal and low temperature is analyzed in order to study the influence of its variable range on welding quality.
针对涩北至格尔木天然气管道复线建设中采用的X60管线钢,根据试验,分析了常温与低温焊接时层间温度变化对管口焊接质量的影响,并指出了防止涩格天然气管道焊接产生冷裂纹的工艺措施。
5) temperature range
温度区间
1.
The thermodynamic calculation of the optimum temperature range for the decomposition of calcium carbonate and the desulfurization by calcium oxide is presented in this paper.
实验分解CaCO3,并进行CaO脱除SO2适宜温度区间的热力学分析和计算,结合CaO的水合活性实验研究,得出了炉内最佳的喷钙脱硫温度为950℃,适宜温度区间为846~1 491℃。
2.
The influence of the temperature span, temperature range, flow time and flow rate were investigated in the experiment.
对温度区间、温度跨度、流动时间和流量几种情况的研究表明在实验范围内,温度跨度和流量的增大会使制冷量减小,流动时间的增加会使制冷量加速减小,温度区间跨越居里点能使制冷量有所增大。
3.
The effect of temperature range for ultrasonic treatment on solidification structure of AZ91D and AZ31B magnesium alloy was investigated and the mechanism of refining solidification structure of magnesium alloy by power ultrasonic treatment was discussed.
研究了超声处理温度区间对AZ91D和AZ31B镁合金凝固组织的影响,探讨了功率超声细化镁合金凝固组织的机理。
6) room temperature
房间温度
1.
The control process of room temperature is complicated and it is difficult for traditional fuzzy control or PID control to get good control performance.
空调房间温度控制是一复杂的控制过程,传统的模糊或PID控制很难得到较好的控制效果,模糊控制和PID控制适当结合控制空调房间温度可使控制效果大大提高。
2.
The study is made on the method to control the start and stop of circulating water pump, and regulate the room temperature, using indoor temperature, floor surface temperature and the both as control parameters.
研究分别以室内温度、地板表面温度及两者作为控制参数,控制循环水泵启停,调节房间温度的方法,发现了地板结构层热延迟性可延迟室内温度的下降,得出了地板辐射供暖系统运行调节规律。
3.
The control system of room temperature is complicated and it is difficult to build the mathematical model of the controlled plant.
房间温度控制是一复杂的控制系统,很难建立精确数学模型,用传统的PID控制很难达到较好的控制效果。
补充资料：铂电阻温度表(见电阻温度表)
铂电阻温度表(见电阻温度表)
表。bod旧nZu wendubiao铂电阻温度表见电阻温
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条