超顶应力梁,over-prestressed beam,音标,读音,翻译,英文例句,英语词典

您的位置：首页 -> 词典 -> 超顶应力梁

1) over-prestressed beam 点击朗读

超顶应力梁

2) prestressed cap beam with extra length 点击朗读

超长预应力盖梁

3) overlength continous prestress beam 点击朗读

超长连续预应力梁

The design of overlength continous prestress beam,the influence of vertical member rigidity,and comparison of several stretching schemes are presented.

介绍了青岛国际会展中心二期工程中超长连续预应力梁的设计方案,着重就竖向构件侧向刚度对梁预应力效应的影响、各种张拉方案进行了分析比较;并对结构中大面积楼盖温度应力的大小、分布规律进行研究,分析过程中考虑了温度荷载的确定、竖向构件侧向刚度、徐变等主要因素的影响,最后提出相应的预应力设计方案。

4) stress in the top coal 点击朗读

顶煤应力

5) roof stress 点击朗读

顶板应力

An theoretic method to calculate roof stress of coal floor; 点击朗读

煤层顶板应力的一种理论计算方法

This paper gives analytic solution fitted to roof stress of coal floor, using analysis method of limitless board of the banding by the complex function in elasticity.

运用弹性力学复变函数求解带状无限长板的分析方法,给出了适用于煤层顶板应力的解析表达式,利用该式,通过数值积分可以比较方便地得到顶板的应力分布。

更多例句>>

6) rupture stress 点击朗读

顶破应力

补充资料：ANSYS工字梁焊缝初应力例子

建立好模型
…..
/SOLU
!*
ANTYPE,0
/INPUT,'input','txt',
/INPUT,'output1','txt',
!*
ISFILE,READ,1,txt, ,0
SOLVE
=====================
!定义残余应力矩阵
I=1
fy=310e6
!定义单元中心坐标数组，初应力数组
*DIM,EleCenter,ARRAY,NumNode,3,1, , ,
*DIM,EleIS,ARRAY,NumNode,1,1, , ,
*DO,I, 1, NumNode,1
!得到单元中心坐标
*GET,EleCenter(I,1,1),ELEM,I,CENT,X
*GET,EleCenter(I,2,1),ELEM,I,CENT,Y
*GET,EleCenter(I,3,1),ELEM,I,CENT,Z
!焊缝位置在X=1.0 到1.05 之间
*IF,EleCenter(I,1,1),GT,1,THEN
*IF,EleCenter(I,1,1),LT,1.05,THEN
*IF,EleCenter(I,2,1),GT,0.5,THEN
!上翼缘初始应力
EleIS(I,1,1)=-20*fy*EleCenter(I,3,1)**2+0.3*fy
*endif
*IF,EleCenter(I,2,1),LT,0.0,THEN
!下翼缘初始应力
EleIS(I,1,1)=-20*fy*EleCenter(I,3,1)**2+0.3*fy
*endif
!腹板初始应力
*if,EleCenter(I,2,1),GE,0.0,THEN
*IF,ELECENTER(I,2,1),LE,0.5,THEN
EleIS(I,1,1)=4.076*fy*(EleCenter(I,2,1)-0.5)**2
EleIS(I,1,1)=EleIS(I,1,1)-0.719*fy
*IF,EleIS(I,1,1),LT,-0.3*fy,THEN
ELeIS(I,1,1)=-0.3*fy
*ENDIF

*ENDIF
*ENDIF
*ENDIF
*ENDIF
*ENDDO
===============
!输出应力数值
*CFOPEN,'1','txt',' '
*DO,I,1,3840
!*IF,EleIS(I,1,1),ne,0.,then
*VWRITE,'!'
(A)
*VWRITE,'! Stress for element',
(A,F)
*VWRITE,'!'
(A)
*VWRITE,'eis,',I
(A,F)
P=EleIS(I,1,1)
*VWRITE,P,0.,0.,0.,0.,0.
(E,E,E,E,E,E)
!*ENDIF
*ENDDO
*CFCLOS

说明：补充资料仅用于学习参考，请勿用于其它任何用途。

参考词条

预应力穹顶顶底板应力顶应力技术顶纤维应力

预应力梁梁端应力拱梁应力梁的应力预应力超高性能混凝土梁

说明：双击或选中下面任意单词，将显示该词的音标、读音、翻译等；选中中文或多个词，将显示翻译。
	您的位置：首页 -> 词典 -> 超顶应力梁 1) over-prestressed beam 超顶应力梁 2) prestressed cap beam with extra length 超长预应力盖梁 3) overlength continous prestress beam 超长连续预应力梁 1. The design of overlength continous prestress beam,the influence of vertical member rigidity,and comparison of several stretching schemes are presented. 介绍了青岛国际会展中心二期工程中超长连续预应力梁的设计方案,着重就竖向构件侧向刚度对梁预应力效应的影响、各种张拉方案进行了分析比较;并对结构中大面积楼盖温度应力的大小、分布规律进行研究,分析过程中考虑了温度荷载的确定、竖向构件侧向刚度、徐变等主要因素的影响,最后提出相应的预应力设计方案。 4) stress in the top coal 顶煤应力 5) roof stress 顶板应力 1. An theoretic method to calculate roof stress of coal floor; 煤层顶板应力的一种理论计算方法 2. This paper gives analytic solution fitted to roof stress of coal floor, using analysis method of limitless board of the banding by the complex function in elasticity. 运用弹性力学复变函数求解带状无限长板的分析方法,给出了适用于煤层顶板应力的解析表达式,利用该式,通过数值积分可以比较方便地得到顶板的应力分布。更多例句>> 6) rupture stress 顶破应力补充资料：ANSYS工字梁焊缝初应力例子建立好模型 ….. /SOLU !* ANTYPE,0 /INPUT,'input','txt', /INPUT,'output1','txt', !* ISFILE,READ,1,txt, ,0 SOLVE ===================== !定义残余应力矩阵 I=1 fy=310e6 !定义单元中心坐标数组，初应力数组 DIM,EleCenter,ARRAY,NumNode,3,1, , , DIM,EleIS,ARRAY,NumNode,1,1, , , DO,I, 1, NumNode,1 !得到单元中心坐标 GET,EleCenter(I,1,1),ELEM,I,CENT,X GET,EleCenter(I,2,1),ELEM,I,CENT,Y GET,EleCenter(I,3,1),ELEM,I,CENT,Z !焊缝位置在X=1.0 到1.05 之间 IF,EleCenter(I,1,1),GT,1,THEN IF,EleCenter(I,1,1),LT,1.05,THEN IF,EleCenter(I,2,1),GT,0.5,THEN !上翼缘初始应力 EleIS(I,1,1)=-20fyEleCenter(I,3,1)2+0.3fy endif IF,EleCenter(I,2,1),LT,0.0,THEN !下翼缘初始应力 EleIS(I,1,1)=-20fyEleCenter(I,3,1)*2+0.3fy endif !腹板初始应力 if,EleCenter(I,2,1),GE,0.0,THEN IF,ELECENTER(I,2,1),LE,0.5,THEN EleIS(I,1,1)=4.076fy(EleCenter(I,2,1)-0.5)2 EleIS(I,1,1)=EleIS(I,1,1)-0.719fy IF,EleIS(I,1,1),LT,-0.3fy,THEN ELeIS(I,1,1)=-0.3fy ENDIF ENDIF ENDIF ENDIF ENDIF ENDDO =============== !输出应力数值 CFOPEN,'1','txt',' ' DO,I,1,3840 !IF,EleIS(I,1,1),ne,0.,then VWRITE,'!' (A) VWRITE,'! Stress for element', (A,F) VWRITE,'!' (A) VWRITE,'eis,',I (A,F) P=EleIS(I,1,1) VWRITE,P,0.,0.,0.,0.,0. (E,E,E,E,E,E) !ENDIF ENDDO CFCLOS 说明：补充资料仅用于学习参考，请勿用于其它任何用途。参考词条预应力穹顶顶底板应力顶应力技术顶纤维应力

©2011 dictall.com