1) tea,glass
玻璃茶具
2) solar(/Brown-colored) glass
茶色玻璃
3) glass mold
玻璃模具
1.
In terms of product characteristics,a practical and efficient design, manufacturing,assembly and testing technology of glass mold is given.
针对产品的特点,给出了一种实用的高效率的玻璃模具设计、制造、装配及调试工艺。
2.
The rule of temperature distribution of glass mold during surfacing were measured with G90-SAT thermal infrared imager.
利用G90-SAT红外热像仪测量了玻璃模具喷焊时的温度分布。
3.
7% of copper, using green-sand mold, putting chill iron in drag to control cooling rate,finer D-type graphite cast iron can be obtained after heating treatment, which is fitted to make the glass mold.
试验结果表明 :选择适宜的基本元素 ( 3 4 %C、2 2 %Si、 0 5 %Mn、 <0 15 %S、 <0 12 %P) ,控制Cr和Cu的含量分别为 0 75 %和 0 7%,用湿砂型和在下型安放大块冷铁的铸造工艺控制冷却速度 ,经热处理后 ,可获得具有良好石墨形态的D型石墨灰铸铁 ,其抗氧化和热疲劳性能分别是普通灰铸铁的 4 1倍和 4 2倍 ,适于制作玻璃模具。
4) glass mould
玻璃模具
1.
Application of Pro/E in glass mould designing;
Pro/E在玻璃模具设计过程中的应用
2.
Recent progress in glass mould materials is reviewed.
介绍了玻璃模具材质的研究进展情况,并讨论了对模具材质性能的要求,指出铸铁仍将是玻璃模具的主要材料,同时对其它的材质也应加以重视,进而展望了今后的研究方向。
3.
5 times as much as that of ferritic cast irons of D type graphite as glass mould materials now, respectively.
对其在85 0℃抗氧化性能和室温耐磨性能进行试验研究表明,与现有的D型石墨铁素体铸铁玻璃模具材质相比,抗氧化性能提高15 0 % ,耐磨性能提高5 0 %。
5) measuring tool of glasses
玻璃量具
1.
The error that was brought out when the measuring tool of glasses was used in the experiments;
玻璃量具对实验分析造成的误差
6) checking tools
玻璃检具
1.
Aiming to the manufacturing of the automobile glass checking tools, the casting technology and the porosity defect of the checking tools were researched in this paper.
本文针对复杂铝合金玻璃检具毛坯的设计和制造,对其铸造工艺、合金成分、缺陷展开了研究。
补充资料：变色玻璃(见光色玻璃)
变色玻璃(见光色玻璃)
photochromic glass
变色玻璃曲otoehromi。glass在萦外尤联，光二中的蓝紫光辐照下，能够在可见光区域产生光吸收而着色，去除辐照后又可逆地回复其原始状态的一种玻璃jm业洛沽该、
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条