1) explosive bonding
爆炸连接
2) chain explosions
连锁爆炸
1.
In chemical industry chain explosions which are composed of two or three type of explosions have always occured in progression.
本文对尿素合成塔连锁爆炸的实例进行了剖析,揭示了其气相爆炸到蒸气爆炸再到蒸气云火球的连锁爆炸机理,并运用相关计算模型对爆炸过程进行了计算,得到了爆炸波最大迭加位置、气相最大爆压、蒸发体积、闪蒸总功、筒体抛射功、TNT当量、以冲击波计的安全距离、火球最大直径、持续时间、辐射通量的计算值。
3) explosive welding
爆炸焊接
1.
Investigation on microstructure at the bonding interface of TiC cermet/steel composite plate prepared by explosive welding;
TiC硬质合金/碳钢爆炸焊接复合板界面微观组织
2.
Numerical analysis of explosive welding interface layer based on δ function;
基于δ函数的爆炸焊接界面应力场数值分析
4) explosion welding
爆炸焊接
1.
This paper presents an experimental study on the inward explosion welding of the clad tube onto the base tube.
本文对基管与复管的外包爆炸焊接进行了实验研究,观察了爆炸焊接界面的组织和波形,分析了用水作为铜管爆炸焊接的柔性芯模在减小基管爆炸缩径上的作用。
2.
By adjusting explosion speed and density, interior explosion welding of the Al /stainless steel thin walled clad tube was researched (L/D≈60).
通过调整爆炸物的爆速、松装密度等参数,采用内爆炸法对铝/不锈钢细长双金属复合管(L/D≈60)的爆炸焊接进行初步的研究。
3.
Under normal conditions,after explosion welding,no welding can be found in the area of the detonator,but serious damages and deformations can be found in its surrounding areas,which affects adversely the quality of the material.
在爆炸焊接工艺中,存在一种称为边界效应的物理现象。
5) explosive bonding
爆炸接合
1.
Some problems dealt with the clad plates by explosive bonding were discussed.
讨论了爆炸接合复合板材研究中存在的问题,认为复合板材接合界面涉及到金属融体的非平衡凝固过程,可能会存在马氏体等固态相变,但不可能形成非晶态。
6) contact explosion
接触爆炸
1.
The test research of steel fibers concrete and steel fibers reinforcedconcrete in anti-contact explosion;
钢纤维混凝土、钢纤维钢筋混凝土抗接触爆炸试验研究
2.
Failure effect of steel-fiber reactive power concrete (RPC) shelter plate under contact explosion;
钢纤维超高强活性混凝土(RPC)遮弹板接触爆炸破坏作用
3.
Damage of thin plate subjected to contact explosion loading;
薄板在接触爆炸载荷作用下的破坏分析
补充资料：核爆炸次声波探测(见核爆炸探测)
核爆炸次声波探测(见核爆炸探测)
nuclear explosion infrasound detection
hebaozha eishengbo tanee核爆炸次声波探测(nueleaf。xplosi。。infrasound deteetion)见核爆炸探坝lJ。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条