1) half-sib-family selection
[遗]半同胞家系选择
2) full sib family selection
[遗]全同胞家谱系选择
3) half-sib
半同胞家系
1.
Analysis and Evaluation on Idioplasmic Resource of Ginkgo biloba s Half-sib;
银杏半同胞家系种质资源质量的分析与评价
2.
Study on Physiological Response of the Activity of Cell Defense Enzymes and Lipid Peroxidation of Slash Pine’s Half-sib under Water Stress;
湿地松优良半同胞家系保护酶活性及脂质过氧化作用对水分胁迫的生理响应
3.
Study on Response to Photosynthetic Characters of Slash Pine s Half-sib Under Water Stress;
水分胁迫下湿地松优良半同胞家系的光合特性响应研究
4) half-sib family
半同胞家系
1.
The study on half-sib family s experimental forest of 20-year-old mason pine show that there are obvious difference among height and resin productivity; and resin productivity was effected very small by temperature, relative humidity and rainfall, but it was influenced evidently by its growth.
以20年生高产脂马尾松半同胞家系子代林为材料进行产脂力分析,结果表明:马尾松半同胞家系间树高和产脂力均具显著差异;树高、胸径、产脂量和产脂力呈极显著的正相关;产脂力与温度呈正相关,与相对湿度及降雨量呈负相关,但均未达显著水平,可见马尾松产脂力受温度、降雨量与相对湿度3个气候因子的影响较小。
2.
Half-sib family growth characters and genetic parameters on 27-year old introducted Japanese black pine and Japanese red pine elites in Zhulin temple of Montain Tai were studied.
通过对泰山竹林寺景区引种27年生的日本黑松和赤松精英树半同胞家系生长特性和遗传参数的研究发现:(1)黑松生长量略优于赤松,它们的平均胸径分别为21。
3.
Study on half-sib family of seed orchard of Larix kaempferi at 15-yr-old;
利用日本落叶松种子园半同胞家系,按田间设计要求建立家系对比试验林,林龄10 a生通过鉴定。
5) Half-sib families
半同胞家系
1.
)half-sib families and twenty clones at ten year s age have been studied on the genetic variations of 21 growth, morphological, physiological and biochemical characters.
)18个半同胞家系和20个无性系为材料,研究了树高、胸径、枝下高、侧枝粗、分枝角度、侧枝数、冠幅、单叶面积、鲜重、干重、鲜/干比、叶绿素a含量、叶绿素b含量、总叶绿素含量、叶片N、P、K含量、光合速率、蒸腾速率、气孔导度、细胞间隙CO2浓度等21个生长、形质、生理生化性状的遗传变异规律。
6) half sib family
半同胞家系
1.
The study on half sib familys experimental forest of 15 year old Massons pine show that there are obvious difference among height, DBH, resin yielding ability, wood specific gravity and tracheid length.
以 1 5年生的半同胞家系马尾松子代林材料进行相关分析 ,结果表明 ,马尾松树高、胸径、产脂力、木材基本密度和管胞长度各性状之间 ,除产脂力与管胞长度的遗传相关呈负相关 (rg=- 0 。
补充资料:选择一个存贮的命名坐标系
如图2-1所示,在 CSYS 构造器对话框中没有 Name 选项可利用,你怎样选择一命名的坐标系? 在选择 (Selection ) 工具条上有一个 Name Selection 域可利用, 你必须定制工具条去激活该选项,如图2-2所示。 在 CSYS Constructor 对话框激活同时, 在选择工具条 Name Selection 域中加入巳存坐标系名, 点击 OK坐标系定位到命名坐标系,如图2-3所示。 | 图2-1 坐标系构造器 |
图2-2 定制工具条 | 图2-3 选择一命名的坐标系 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条