1)  pinching
"剥裂,衬砖在升温时挤压造成"
2)  scrape,ripping,strip
3)  exfoliation
剥离
1.
Exfoliation Reaction and Recombination of the Layered Hydroxide Zinc Benzoate with a Basal Spacing of 1.44 nm;
层间距为1.44nm层状氢氧化苯甲酸锌剥离重组行为研究
2.
Reason analysis and countermeasures of the trouble of the integrated wheel exfoliation for DF_(4D) and DF_(11) locomotives;
DF_(4D)、DF_(11)型机车整体车轮剥离的原因分析及对策
3.
The property and organieal modification of montmorillonite are also reviewed,and it is indicated that the key issue in preparing epoxy/montmorillonite nanocomposites at present is to achieve exfoliation or delamination of the aggregates in.
阐述了蒙脱土的性质及其在基体树脂中的剥离机理、环氧树脂/蒙脱土纳米复合材料的制备方法。
4)  spalling
剥落
1.
Spalling and Preventive Measures of Cast Hot-Strip Roll;
铸造热轧带钢工作辊的剥落失效与预防措施
2.
It has been analyzed the causes for both heavy surface spalling and "side spalling" of back-up roll for hot strip mill.
本文对梅山1422热连轧支撑辊剥落掉块和辊身边部“掉肩”进行了深入的分析,结果表明加工硬化、磨损不均匀、接触疲劳、辊身边部倒角设计不合理及工作层内缺陷是造成轧辊剥落的主要原因。
3.
The paper analyses the spalling of 5Cr forging cold work rolls in the CSP Plant of Baotou Steel Corp.
对包钢薄板厂5Cr锻钢冷轧工作辊连续发生的剥落事故进行分析,指出了裂纹是导致剥落的根本原因,而轧辊的材质、磨削工艺、检测手段是产生剥落的影响因素,同时针对所存在的问题在配辊管理、磨削制度、检测制度三方面提出了技术改进措施。
5)  desquamation
剥落
1.
The analysis shows that the beforehand physical defects and carbonization may be the reason for barrier's desquamation.
用电镀Cr-C的方法在氢化锆表面建立的氢渗透阻挡层,在1atm的CO2气氛中和700℃下保温72小时,阻挡层局部发生脱皮和剥落,用SEM对其表面进行观察。
2.
By means of chemical analysis,rigidity test,metallographic examination and fracture analysis,it was found that the main reason for the backup roll's desquamation was possible crack headspring which was offered by impurity in interior tissue.
中厚板轧机上的锻钢支撑辊在使用中后期出现不同程度的剥落现象,致使轧辊损耗加快。
3.
Some common types of work roll desquamation in rolling of medium and heavy plate are introduced.
介绍了在中厚板轧制中几种常见的工作辊剥落类型,联系实际分析其产生的原因,并提出了相关的预防措施。
6)  delamination
剥层
1.
Under low impact cycles,the forms of damage are mainly plastic deformation and plastic accumulation;but for high impact cycles,surface crush and delamination occurs because of the plastic exhaustion of the central zone of impact wear scar,and the thick.
结果表明在本试验条件下,磨损体积损失随冲击次数的增加呈非线性增大;在低循环次数下,冲击磨损损伤形式主要为塑性变形及塑性堆积;当循环次数较高时,冲击坑中心由于塑性耗竭而出现表面压碎及剥层磨损,且由激光显微镜测得的剥层厚度在0。
参考词条
补充资料:剥裂
1.撕裂。 2.割裂。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。