1) maximum specific growth rate
最大生长比速
2) maximum specific growth rate
最大比生长速率
1.
The relationship between N/P ratios and maximum specific growth rate of red tide algae was analyzed according to Shelford\'s law of tolerance to study the response mechanism between N/P ratios and red tide algae,and the tolerance model between specific growth rate of red tide algae and N/P ratios was established.
为研究赤潮藻类的氮磷比耐受性响应机制,总结了赤潮藻类最大比生长速率与氮磷比的关系,以谢尔福德耐受定律为依据,建立了赤潮藻类最大比生长速率与氮磷比的耐受性模型,并以中肋骨条藻(Skeletonema costatum)为例进行实验验证。
2.
The batch respirometric method was applied for the determination of the concentrations and the maximum specific growth rate(μ^A) of autotrophic biomass (XA) in mixed liquors from aerobic tanks of a full-scale wastewater treatment plant with anaerobic/anoxic/aerobic process and a pilot-scale anaerobic/aerobic process.
利用批式呼吸计量法测定了实际污水处理厂厌氧/缺氧/好氧工艺和小试装置厌氧/好氧工艺好氧池内自养菌(XA)的浓度及其最大比生长速率常数(^μA)。
3) maximum growth rate
最大生长速率
1.
According to pathogen s maximum growth rate, clone direct doubling time and results of cluster analysis, the tested culture ( Botryosphaeria dothidea )was divided into 4 types of temperature dependence.
通过对菌落最大生长速率、直径加倍时间的测定和所得结果的聚类分析 ,将供试菌株分为 4个温度依赖型 ,并分析了杨树溃疡病菌 ( Botryosphaeria dothidea)的极限温度和对连续高温的忍受能力及扩散趋势。
4) heterotrophic maximum specific growth rate
异养菌最大比增长速率
1.
Sensitivity analysis showed that the performance of activated sludge system was affected remarkably by heterotrophic decay rate, heterotrophic maximum specific growth rate and autotrophic maximum specific growth rate, so these parameters were studied.
灵敏度分析表明,ASMCN模型中的异养菌衰减系数(bH)、异养菌最大比增长速率(μmH)和自养菌最大比增长速率(μmA)对活性污泥系统的性能有显著影响,着重研究了这3个参数。
5) autotrophic maximum specific growth rate
自养菌最大比增长速率
1.
Sensitivity analysis showed that the performance of activated sludge system was affected remarkably by heterotrophic decay rate, heterotrophic maximum specific growth rate and autotrophic maximum specific growth rate, so these parameters were studied.
灵敏度分析表明,ASMCN模型中的异养菌衰减系数(bH)、异养菌最大比增长速率(μmH)和自养菌最大比增长速率(μmA)对活性污泥系统的性能有显著影响,着重研究了这3个参数。
6) the maximum slenderness-ratio
最大长细比
1.
Using provision of centrally compressed lattice columns,the maximum slenderness-ratio of the T-shaped-cross-section component above the opening and the maximum width of opening are decided.
应用轴压格构柱的有关规定,确定了空腹受弯钢构件孔口上方受压T形截面杆件的最大长细比和开口宽度的最大值;为确保板件具有一定的刚度和强度,提出了空腹受弯钢构件孔口上方腹板和孔间腹板的最小尺寸以及孔间腹板的强度验算式;基于薄板的弹性稳定理论,确定了在纯弯状态下空腹受弯钢构件孔口上方腹板和孔间腹板的最大高厚比。
补充资料：最大生长比速
分子式：
CAS号：
性质：也称比生长速率。单位质量的细胞在单位时间内所增加的细胞质量称为菌体的生长比速(μ)，单位为s-1。在对数生长阶段，若没有抑制或限制微生物生长的因素存在，微生物的比生长速率可达到某一最大值(μm)。菌体的最大生长比速和细胞种类、培养温度、培养基组成等因素有关。
CAS号：
性质：也称比生长速率。单位质量的细胞在单位时间内所增加的细胞质量称为菌体的生长比速(μ)，单位为s-1。在对数生长阶段，若没有抑制或限制微生物生长的因素存在，微生物的比生长速率可达到某一最大值(μm)。菌体的最大生长比速和细胞种类、培养温度、培养基组成等因素有关。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条