1) injection compression moulding compound
注射-压缩模塑料
2) IMC
注射-压缩模塑料
3) injection
注射
1.
Development of mould combining punching and injection forming for switch contact finger socket;
开关触片座冲压注射组合模设计
2.
Influence of injection conditions on mechanical performance of polyamide-6;
不同注射条件对尼龙6力学性能的影响(英文)
3.
The relationship between the PA molding shrinkage and the injection process conditions;
PA成型收缩率与注射工艺条件的关系
4) Inject
注射
1.
Determination of Volatile Phenol in Water by the Segment Flow Injection Analysis;
间隔流动注射法测定水中挥发酚方法概述
2.
Ethanol Injection Treatment of Simple Clinical Study of Breast Cysts;
无水乙醇注射法治疗单纯性乳腺囊肿的临床探讨
3.
Objective To investigate the effect of botulinum toxin A(BTA) injected into vocal cords for the treatment of adductor spasmodic dysphonia (SD) by direct lanyngoscopy.
目的 探讨双侧声带注射 A型肉毒毒素治疗内收性痉挛性发声障碍疗效。
5) injection molding
注射
1.
The filling time steps were adaptively adjusted for flow calculation of injection molding;sub time steps of computing temperatures were calculated for each node according to local courant number,and the heat transfer analysis was conducted by the filled order of nodes.
在注射流动分析中,依据多个时间步长流过一个单元层的准则,自动调节流动分析的时间步长;而在温度计算时每个结点依据其Courant数采用不同的子时间步长,并且按着结点的注满顺序进行传热分析。
2.
The adaptively implicit algorithm was applied for numerical analysis of injection molding, and the fountain effects in melt fronts were numerical approximated.
在注射流动与传热分析的中面模型采用自适应隐式控制体积法,并在熔体前沿进行泉涌效应的近似处理。
6) injections
注射
1.
Clinical study of the Yinxingye injections for treatment of cereb ral hemorrhage;
银杏叶注射液治疗脑出血的临床研究
2.
Verification of “Polysaccharide nucleic acid fraction of Bacillus Calmette Guerin in treatment of verruca vulgaris by lesional injections” published by “Chinese Journal of New Drugs and Clinical Remedies”;
对贵刊刊登《卡介菌多糖核酸注射液皮损内注射治疗寻常疣》的验证
3.
Polysaccharide nucleic acid fraction of Bacillus Calmette Guerin in treatment of verruca vulgaris by lesional injections;
卡介菌多糖核酸注射液皮损内注射治疗寻常疣
参考词条
补充资料：注射-压缩模塑料
分子式：
CAS号：
性质：注射-压缩模塑用不饱和聚酯模塑料。ZMC不表示实在含义，包含三层意义——模塑料、注射模塑机械、模具。由于使用注射-压缩模塑成型，对玻纤破坏性小，定向性也小，制品机械强度(尤其是冲击强度)明显高于BMC。以汽车面板为例，冲击强度较BMC注射产品提高117％，弯曲弹性模量提高38％，弯曲强度提高5％(两种模塑料的玻纤含量均为25％)。ZMC的玻纤长度一般为25mm，类似于BMC。生产速度明显高于SMC。主要用于注射-压缩成型。
CAS号：
性质：注射-压缩模塑用不饱和聚酯模塑料。ZMC不表示实在含义，包含三层意义——模塑料、注射模塑机械、模具。由于使用注射-压缩模塑成型，对玻纤破坏性小，定向性也小，制品机械强度(尤其是冲击强度)明显高于BMC。以汽车面板为例，冲击强度较BMC注射产品提高117％，弯曲弹性模量提高38％，弯曲强度提高5％(两种模塑料的玻纤含量均为25％)。ZMC的玻纤长度一般为25mm，类似于BMC。生产速度明显高于SMC。主要用于注射-压缩成型。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。