2) ultra-fine grinding
超细粉碎
1.
Progress of ultra-fine grinding and classifying techniques in China;
中国超细粉碎和精细分级技术现状及发展
2.
Through experimental studies on ultra-fine grinding of molybdenite,it can be found that there is the effect of density in grinding,the ratio of ball to ore,ball distribution,rotating speed of mill, the consumption of dispersant,grinding time on grinding process.
对润滑剂级辉钼矿进行超细粉碎研究,研究了磨矿浓度、球矿比、球径配比、搅拌转速、水溶分散剂用量、磨矿时间对超细磨矿结果的影响。
3.
The present states of the ultra-fine grinding technology and equipment for non-metallic ores are reviewed in recent years in China.
综述了我国近年来非金属矿超细粉碎技术和设备的发展现状 ,指出了制约国内技术和设备发展的几个问题 ,结合超细粉体粒子微细化、表面活性化、用途功能化、组成高纯化、产品系列化的性能要求 ,提出了我国超细粉碎技术今后的发展方向。
3) ultrafine grinding
超细粉碎
1.
Influence of liquid medium on ultrafine grinding of pyrite;
液体介质对黄铁矿超细粉碎的影响
2.
Study of ultrafine grinding of pyrite catalyst used in direct coal liquefaction;
煤直接液化用黄铁矿催化剂超细粉碎的研究
3.
Affecting mechanism of grinding aid during ultrafine grinding;
超细粉碎过程助磨剂的作用机理
4) ultra-fine comminution
超细粉碎
1.
Study on ultra-fine comminution to coal using effect of pressure released;
利用压力释放效应对煤进行超细粉碎的研究
2.
In the meantime,the cause of ultra-fine comminution of LDPE with turbulence mill at atmospheric temperature was analyzed,also.
在湍流粉碎机上,进行了常温低密聚乙烯超细粉碎的转速、入料粒度和入料速度的实验。
3.
Datong coal-series kaolin can be used as paper coating after being processed by chemical blanching, ultra-fine comminution and calcine.
大同含炭硬质高岭土经化学漂白、超细粉碎和煅烧处理,可获得造纸涂布用煅烧高岭土。
5) Dispersion and Fining
粉碎细化
6) superfine crushing
超细粉碎
1.
Actualities and progressing trends of superfine crushing techniques;
超细粉碎技术现状及发展趋势
2.
Disaggregation of nanodiamond hard aggregates by mechano chemical superfine crushing has been studied.
利用超细粉碎机械化学法进行了纳米金刚石硬团聚体的解聚研究 ,测试了 2种优化助磨剂对解聚的活化指数 ,分析了 2种助磨剂加入粉碎前后及随后化学机械分散处理成悬浮液后纳米金刚石表面官能团的变化和表面电性、最终悬浮液的粒度、粉碎前后纳米金刚石的晶体结构。
3.
The ZnO varistors with high voltage gradient were fabricated by superfine crushing and low temperature sintering process.
通过超细粉碎和低温烧结工艺。
补充资料：细粉碎
分子式：
CAS号：
性质：一种粉碎过程。一般进料尺寸为20～100mm，其粉碎比为5～7。
CAS号：
性质：一种粉碎过程。一般进料尺寸为20～100mm，其粉碎比为5～7。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条