2) bisphenol-F epoxy resin
双酚-F环氧树脂
1.
The kinetics of the cure reaction for a system of bisphenol-F epoxy resin with tetrabromophthalic anhydride as a curing agent, was studied by means of differential scanning calorimetry (DSC).
本文用示差扫描量热法(DSC)研究了双酚-F环氧树脂和固化剂四溴苯酐(PHT4)的固化反应动力学。
3) bisphenol F epoxy resin
双酚F环氧树脂
1.
New type of bisphenol F epoxy resin with low viscosity, solvent resistance, and high impact resistance, and impregnation of the fiber and glass fiber reinforced plastic composite performance, the use of low cost has been good for the manufacture of wind power blade-based system for materials.
新型双酚F环氧树脂具有粘度低、耐溶剂性强、耐冲击性能高、对纤维浸渍性和与玻璃钢复合性能好、使用成本低等优点而被看好用于制造风电叶片基制材料。
4) bisphenol formaldehyde/resorcin copolymerization epoxy resin
双酚F/间苯二酚共聚型环氧树脂
1.
Study on bisphenol formaldehyde/resorcin copolymerization epoxy resin cured with dicyandiamide;
双氰胺固化双酚F/间苯二酚共聚型环氧树脂的研究
5) bisphenol A epoxy resin
双酚A型环氧树脂
1.
The effects of curing temperature and the content of on the curing speed of PSN-1 polysilazane/bisphenol A epoxy resin curing system were discussed.
研究了聚硅氮烷(PSN-1)/双酚A型环氧树脂固化体系的固化温度、PSN-1用量对固化速度的影响;并利用热重分析(TGA)研究了PSN-1用量对固化树脂高温残余质量分数的影响,对固化机理进行了初步探讨。
6) bisphenol A type epoxy resin
双酚A型环氧树脂
1.
The test conditions of determination of bisphenol A type epoxy resin by HPLC were established.
确定了高效液相色谱法分析双酚A型环氧树脂组成成分实验条件。
2.
Polyisocyanurate rigid foamed plastic modified by bisphenol A type epoxy resin has been prepared by isocyanate(MDI),polyether polyols(403,4110),bisphenol A type epoxy resin,foaming agent,foam homogeneoas reagent and other raw materials.
采用异氰酸酯(MDI)、聚醚多元醇(403、4110)、双酚A型环氧树脂、发泡剂、均泡剂等原料,制备了双酚A改性聚异氰脲酸酯硬质泡沫塑料。
补充资料：双酚F型环氧树脂
分子式：
CAS号：
性质：俗称双酚F型环氧树脂。含二酚基甲烷的低黏度缩水甘油醚型环氧树脂。黏度3.3Pa·s，仅为双酚A型环氧树脂的1/3～1/4，环氧当量169，相对密度1.16～1.18。常温固化物拉伸强度45.1MPa，弯曲强度81.3MPa，压缩强度122.5，冲击强度3.92kJ／m2(而加热固化物则较常温固化物的机械强度分别高20％～50％)。强度、热稳定性和化学稳定性均优于双酚A型环氧树脂。前者在稀酸中浸泡30天后增重1.46％～2.50％，后者为2.45％～3.05％。由双酚F与环氧氯丙烷缩聚而得。可有3种异构体。加工方法与双酚A型环氧树脂类似。主要用作涂料、电子元件铸塑料、衬里、地板材料和复合材料。其增强塑料可用作某些结构件。
CAS号：
性质：俗称双酚F型环氧树脂。含二酚基甲烷的低黏度缩水甘油醚型环氧树脂。黏度3.3Pa·s，仅为双酚A型环氧树脂的1/3～1/4，环氧当量169，相对密度1.16～1.18。常温固化物拉伸强度45.1MPa，弯曲强度81.3MPa，压缩强度122.5，冲击强度3.92kJ／m2(而加热固化物则较常温固化物的机械强度分别高20％～50％)。强度、热稳定性和化学稳定性均优于双酚A型环氧树脂。前者在稀酸中浸泡30天后增重1.46％～2.50％，后者为2.45％～3.05％。由双酚F与环氧氯丙烷缩聚而得。可有3种异构体。加工方法与双酚A型环氧树脂类似。主要用作涂料、电子元件铸塑料、衬里、地板材料和复合材料。其增强塑料可用作某些结构件。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条