1) insulating ring
保温圈
2) thermal insulation
保温
1.
Analysis on the leakage of thermal insulation roof waterproofed with coiled material;
卷材防水保温平屋面渗漏分析
2.
Scheme alternatives for internal thermal insulation construction utilizing sandwich slab in cast-in-place balcony of high-rise building;
高层住宅现浇阳台泰柏板内保温施工方案选择
3) heat preservation
保温
1.
Discussion on zero heat preservation during quenching/normalizing structural steel;
结构钢淬(正)火热处理零保温探讨
2.
Study and computer simulation of heat preservation in irrigetion works;
渠系水工建筑物保温措施的研究及计算机模拟
3.
Discussion on application of XPS heat preservation system on heat preservation of building s exterior wall;
浅谈XPS保温系统在建筑外墙保温中的应用
4) insulation
[英][,ɪnsju'leɪʃn] [美]['ɪnsə'leʃən]
保温
1.
How to improve thermal insulation of PVC-U steel windows;
浅谈如何提高PVC-U塑料窗的保温性能
2.
Correctly select polyurethane rigid foam——brief introduction of 《Technical code for polyurethane rigid foam insulation and waterproofing engineering》;
硬泡聚氨酯材料的正确选用——《硬泡聚氨酯保温防水工程技术规范》简介
3.
Standard JC/T 998-2006《Spray polyurethane foam insulation material》briefing;
JC/T998—2006《喷涂聚氨酯硬泡体保温材料》标准介绍
5) heat insulation
保温
1.
Application of fireproof fiber spray-applied coating in the heat insulation of heating furnace;
耐火纤维喷涂在加热炉锅炉保温中的应用
2.
Construction method of heat insulation and waterproof roof with polyurethane foam;
发泡聚氨酯保温防水屋面施工方法
3.
Low-Temperature Air-Supply Duct an d Heat Insulation in Ice-Storage Air Conditioning System;
冰蓄冷空调系统中的低温送风风管和保温
6) Holding
[英]['həʊldɪŋ] [美]['holdɪŋ]
保温
1.
Effect of Holding Technology at Intermediate Roll Table in Hot Continuous Rolling on Phase Transformation and Structure of Low Carbon Steel;
热连轧中间辊道保温工艺对低碳钢相变和组织的影响
2.
Improving Holding Effect of Electric Furnace in Non-Ferrite Metal foundry;
提高有色铸造车间电炉的保温效果
3.
The influence of the holding time in different conditions of deforming temperature as well as primal austenite grain sizes on the microstructure of transformation were investigated.
通过热模拟实验 ,考察了不同变形温度和不同奥氏体晶粒尺寸等条件下保温对低碳钢形变后组织演变的影响。
补充资料:保温圈
分子式:
CAS号:
性质:为高大直立设备(如塔器)外部保温材料的支承圈。通常用厚度为4mm,宽度为80~120mm的扁钢水平地焊接在设备的外缘。为了省料和装配方便起见,保温圈不是整环,而是中间断开20~30mm,由四段组成。在圈的外缘每隔50mm钻有声5mm的小孔,以固定保温材料之用。一般沿塔高每隔3m左右焊一圈。
CAS号:
性质:为高大直立设备(如塔器)外部保温材料的支承圈。通常用厚度为4mm,宽度为80~120mm的扁钢水平地焊接在设备的外缘。为了省料和装配方便起见,保温圈不是整环,而是中间断开20~30mm,由四段组成。在圈的外缘每隔50mm钻有声5mm的小孔,以固定保温材料之用。一般沿塔高每隔3m左右焊一圈。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条