1) thermal test
热态试验
1.
The campaign of blast furnace is prolonged by using copper staves, and the thermal performance of the staves is determined by thermal test and numerical simulation.
通过热态试验和数值模拟的方法来测试其热态性能。
2.
The thermal test system of cooling stave was designed and established to put up the industrial experiment of the heat transfer for the cast steel cooling stave and ductile iron cooling stave.
设计并建造了冷却壁热态试验系统,对铸钢冷却壁和球墨铸铁冷却壁的换热效果进行了工业模拟试验。
3.
The strain of cold surface and temperature of the stave under high thermal load were measured through thermal test,and the fields of temperature,strain and stress were also calculated through numerical simulation.
通过热态试验测量了高温下冷却壁的温度分布和冷面应变分布,通过数值模拟计算了冷却壁的温度场和应力应变场。
2) hot state test
热态试验
1.
Therefore,hot state tests were carried out,on an internally circulating fluidized bed test rig,using coal as fuel.
因此,在1个内循环流化床燃烧试验台上进行了以煤为燃料的热态试验。
3) experimental modal
试验模态
1.
The experimental modal analysis of model of the simplified hull in the cabin section;
简化的舱段船壳模型试验模态分析
2.
Reducing vibration of circular saw based on experimental modal analysis
基于试验模态分析的圆锯片降低振动研究
3.
Using the PULSETM,the multi-analyzer system type 3560c and Me’ScopeTM,the family of post-test analysis tools,the experimental modal of bench drilling machine were analyzed,and rationality of its design was werifiered.
选用PULSETM-3560C便携式多分析仪系统和Me’ScopeTM模态分析软件对台式钻床进行试验模态分析,验证了台式钻床设计的合理性。
4) dynamic test
动态试验
1.
Development of dynamic test-bed for fluid flow machine;
流体机械动态试验台研制
2.
The results show that the toughness and displacement at peak load decrease with the fall of test temperature; the displacement at peak load of dynamic test is less than that of static test at the same temperat.
在不同试验温度下,对X70管线钢缺口沿厚度方向的标准夏比V型缺口试样进行动态试验和静态试验,研究了X70管线钢的力学性能与加载速率的关系。
3.
The whole designing scheme of dynamic test system was introduced,the working principle of ECU in diesel engine was explained,and the controlling performance of ECU in the dynamic test was analyzed and researched.
介绍了柴油机动态试验系统的总体设计方案和ECU对发动机控制的工作原理,并针对ECU在动态试验中的控制性能进行了研究。
5) static test
静态试验
1.
The results show that the toughness and displacement at peak load decrease with the fall of test temperature; the displacement at peak load of dynamic test is less than that of static test at the same temperat.
在不同试验温度下,对X70管线钢缺口沿厚度方向的标准夏比V型缺口试样进行动态试验和静态试验,研究了X70管线钢的力学性能与加载速率的关系。
2.
Then static test on the servo-valve has been done on the servovalve test-bed.
为进行液压流体脉动的主动消振,设计了基于压电陶瓷的直接驱动伺服阀,并利用AMESim液压仿真软件对其进行了建模与仿真,并在伺服阀实验台上对其进行了静态试验。
3.
In this case exit oil pressure remains constant, while in a turbine s static test the main oil pump, which supplies oil to the secondary and tertiary loop, has a variable exit pressure which is a function of the speed of rotation.
该文以上海汽轮机厂N1 2 35型汽轮机调速系统为例 ,探讨了用高压电动油泵进行静止试验的情况 ,由于其出口压力维持不变 ,静态试验时 ,供到二、三次油路的主油泵出口油压为一变数 ,系转速的函数 ,由此会产生差异 ,文中指出在同类机组进行调速系统试验时 ,此差异带来的误差很小 ,并推荐一种由静止试验和静态试验结果作四象限图的方法。
6) Dynamic testing
动态试验
1.
Making use of the precise displacement controlling of the material testing machine,the dynamic testing of metal rubber/rubber composite laminated energy dissipator is done.
采用电液伺服材料试验机的位移加载方式,对金属橡胶/橡胶复合叠层耗能器进行动态试验研究。
补充资料：热稳定性试验
分子式：
CAS号：
性质：考察橡胶在高温下的热能稳定性试验。是评价耐热橡胶性能的重要项目。常见的有空气热老化试验、热重分析试验、马丁耐热试验和维卡耐热试验等。
CAS号：
性质：考察橡胶在高温下的热能稳定性试验。是评价耐热橡胶性能的重要项目。常见的有空气热老化试验、热重分析试验、马丁耐热试验和维卡耐热试验等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条