说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 点式处理
1)  Pointed approach
点式处理
2)  joint treatment
节点处理
1.
Based on secondary waterproofing project for Shenzhen Children s Palace the article discusses mainly waterproofing measures that should be taken after waterproof layers cracked due to difference in coefficient of deformation between steel and concrete roofs and gives emphasis to important role the joint treatment plays in waterproofing project.
通过深圳市少年宫屋面二次防水工程的施工实践,着重讨论了因钢结构屋面和混凝土屋面变形系数不同而产生防水层拉裂现象后,进行防水处理措施;强调了节点处理在整个防水工程中所起的重要作用;总结了针对造型独特、由不同材料组成的结构及造型形成的相贯线、接缝等的防水二次深化设计。
3)  joints treatment
节点处理
1.
Combined with practical work and the procedure of top-down construction method the construction methods of underground continuous wall,intermediate supporting pile,earth excavation of basement are introduced as well as the measures for joints treatment.
结合具体工程实例,根据工程逆作法施工工序,介绍了地下连续墙、中间支承柱、地下室土方的施工方法,探讨了节点处理措施,经过基坑周边沉降及位移观测,该逆作法的施工效果符合质量控制要求。
4)  point cloud processing
点云处理
1.
Surface provides us with point cloud processing and curve editing and UG provides us with solid modeling,with which the right STL file can be established and the integration of reverse engineering and rapid prototyping is achieved.
通过Sur-face软件强大点云处理功能、曲线编辑功能及UG软件的实体生成功能,形成了无错的STL格式文件,成功的实现了RE/RP的集成,最后指出对不同产品选择适当的CAD建模方法是实现快速原形的关键。
2.
Through research and experiment,JXTA technology was applied to point cloud processing.
介绍了P2P技术,讨论了JXTA技术及其特点,并通过研究和实验把JXTA技术应用到点云处理中。
5)  plot processing
点迹处理
1.
Implementation of the radar plot processing system based on VxWorks;
基于VxWorks的雷达点迹处理系统的实现
6)  hotspot treatment
热点处理
1.
In order to deal with the local hotspot caused by extreme access in enterprise information distributed storage,a novel distributed storage hotspot treatment strategy was presented.
为解决企业信息分布式存储中因局部访问过热而导致的一系列问题,提出了新型的分布式存储热点处理策略。
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条