1) key oil film bearing sleeve
有键油膜轴承锥套
1.
Analyzing key oil film bearing sleeve with limit element statics,the paper introduces the distortion rule and stress distribution of key groove during sleeve groove and oil film pressure is at the different relatively position, and discusses the effect of stress distribution due to sleeve distortion acted by key groove.
本文应用有限单元法,对有键油膜轴承锥套进行了有限元静力分析,了解了锥套键槽与油膜压力处于不同的相对位置时键槽的变形规律和应力分布状态,探讨了键槽对锥套的变形及应力分布的影响。
2) oil-film bearing
油膜轴承
1.
Study on contact damage of sleeve of oil-film bearing in rolling mill;
大型轧机油膜轴承锥套损伤问题研究
2.
The Oil-film Temperature Fild Analysis of Oil-film Bearing Based on ANSYS;
基于ANSYS的油膜轴承油膜温度场分析
3.
This paper presented the mechanism of fretting fatigue failure that happened on the contact surfaces between sleeve and roll neck of oil-film bearing under the rolling load.
研究了油膜轴承锥套与辊颈接触表面在轧制载荷作用下发生微动疲劳损伤的力学机理。
3) oil film bearing
油膜轴承
1.
Design and analysis of structural parameters for capillary oil film bearing
毛细管节流的油膜轴承结构参数设计分析
2.
A modern large-scale mill's perfect bearing——oil film bearing,a key part of the mill,has many advantages,such as large carrying capacity,long service life,wide speed range,low friction coefficient,small configuration size,strong impact resistance,etc.
现代大型轧机的理想轴承——油膜轴承是轧机的关键部件,具有承载能力大、使用寿命长、速度范围广、摩擦因数小、结构尺寸小、抗冲击能力强等优点。
3.
Baosteel Branch's 5m mill is the first especially wide and heavy plate production line,and oil film bearing is one part of its main equipment.
宝钢分公司厚板厂5m轧机是国内第一条特宽幅厚板生产线,油膜轴承是厚板轧机的主要设备之一,正确认识和掌握其特点是提高厚板生产的关键环节。
5) tapered bearing ring
圆锥轴承套圈
1.
The coning deformation is easily caused after tapered bearing ring is quenched,rings is made cooling uniform during quenching,reduced coning deformation and greatly decreased rejects rate for changing placement method.
圆锥轴承套圈淬火后易产生锥度变形,通过改变摆放方法,使淬火时冷却均匀,减少锥度变形,大大降低因锥度变形率超差而造成的废品。
6) filmatic bearing oil
油膜轴承油
1.
The present status abroad,domestic level and its application of filmatic bearing oil were described.
介绍了油膜轴承油国外现状和国内水平及其应用简况，分析了油膜轴承用油国产化的人为障碍及今后国产化的希望。
2.
The performances and the results of service test of 460 filmatic bearing oil used for morgan type no-twist wire rod mills at high speed were presented.
介绍了摩根型无扭高速线材连轧机用４６０号油膜轴承油的性能及工业使用试验结果。
3.
The formulation of 220 anti-wear type filmatic bearing oil was described, and the package's formulation was determined.
介绍了220抗磨型油膜轴承油的研制经过，确定了复合添加剂配方，研制的油品性能与MobilVacuoline533和ShellVitreaM220油相当。
补充资料：油膜轴承油
分子式：
分子量：
CAS号：
性质：为抗氧防锈型润滑油。具有良好的粘温性能、抗氧化性、防锈性及抗泡沫性等。目前最重要为21号油膜轴承油，适用于轧钢机的动压、静压、动静压油膜轴承，也可用于低速、重负荷大型机械的滑动轴承。以原油经过常减压蒸馏、丙烷脱沥青、深度溶剂精制、溶剂脱蜡及补充精制所得润滑组分，再加入抗氧、防锈、抗泡沫添加剂调制而成。
分子量：
CAS号：
性质：为抗氧防锈型润滑油。具有良好的粘温性能、抗氧化性、防锈性及抗泡沫性等。目前最重要为21号油膜轴承油，适用于轧钢机的动压、静压、动静压油膜轴承，也可用于低速、重负荷大型机械的滑动轴承。以原油经过常减压蒸馏、丙烷脱沥青、深度溶剂精制、溶剂脱蜡及补充精制所得润滑组分，再加入抗氧、防锈、抗泡沫添加剂调制而成。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条