1) steel-concrete composite beam
钢-砼叠合梁
1.
And mechanical characteristics of copulae of steel-concrete composite beam,which has different space and rows of shear connectors,different ratio of lateral direction reinforcement and different height of steel beam,is calculated and analyzed.
利用大型通用有限元软件 ABAQUS 对叠合梁结构进行了数值模拟,计算分析了不同剪力键布置(间距和排数)、横向钢筋配筋率和钢梁高度时叠合梁接合部受力特性,为钢-砼叠合梁的设计提供参考和依据。
2) IF steel
IF钢
1.
The Static Recrystallization Behavior of IF Steel after Ferrite Hot Deformation;
IF钢热变形铁素体的静态再结晶行为
2.
Influence of MgO-SiC material with Al powder on silicon content of IF steel;
含铝粉的MgO-SiC材料对IF钢硅含量的影响
3.
TEM study on recrystallization mechanism of IF steel;
IF钢冷轧及再结晶初期微观组织的TEM研究
3) steel
钢
1.
Analysis of characteristic zones of isothermal superplastic welded joint of heterogeneous steels;
异种钢恒温超塑焊接头特征区域分析
2.
Determination of total boron in steel with microwave digestion and Inductively Coupled Plasma Atomic Emission Spectrometry;
微波消解/ICP-AES法测定钢中全硼
3.
Approach to Research on Cracking of Steel and Relevant Concerns;
钢的裂纹研究思路及应注意的问题
4) interstitial free steel
IF钢
1.
Effect of cross-shear rolling on texture of interstitial free steel;
异步冷轧工艺对IF钢织构的影响
2.
Imitation Test of Batch Annealing and Continuous Annealing Recrystallizing of Interstitial Free Steel;
IF钢罩式退火与连续退火再结晶模拟试验
3.
Effect of Hot Rolling Finishing Temperature on Structure and Pro perty of Ti+Nb treated Interstitial Free Steel Sheet;
终轧温度对Ti+Nb处理的高强IF钢板组织和性能的影响
5) steels
钢
1.
The law of atmospheric corrosion of 4 steels in Shenyang area was studied by means of atmospheric exposure tests and their corrosion products were analyzed by XRD and IRAS.
通过大气暴露试验和实验室的浸渍干燥湿润复合循环试验 ,结合腐蚀产物的表面分析 ,研究了 4种钢在沈阳地区的大气腐蚀规律和模拟大气腐蚀过程的腐蚀规律 。
2.
In this paper,abrasion behavior of carbonitriding steels used in the manufacture of pump body is studied.
研究了碳氮共渗钢制作的水泵体的磨损特性。
3.
The cyclic oxidation of four different steels without and with aluminide coatings under the condition of quenching in sea water has been studied.
对 4种不同级别的钢在 6 0 0℃～ 80 0℃氧化和海水淬冷交替作用下的循环腐蚀行为进行了研究 。
6) IF steel
IF 钢
1.
In the present works,by improvement in design of compressed specimen and some effective measures to restrain plastic deformation in the gripped portion,the problems of low strain rate and insufficient strain for simulating continuous hot rolling of IF steel by Gleeble 1500 had been overcome.
通过限制热压缩试样外端区参与塑性变形的改进措施,解决了模拟连轧过程中应变速率低、总应变程度不足的问题,在实验室成功地模拟了武钢 IF 钢热轧过程。
2.
To produce super low carbon steel which final carbon content is lower than or equal to 13×10~(-6),factors which effect decarburization were analyzed thermodynamically and kinetically,and measures were taken to further reduce the final carbon content of IF steel,preparing for mass production of super low carbon steel were proposed.
本文简单介绍了宝钢股份宝钢分公司炼钢厂为生产成品碳≤13×10~(-6)的极低碳 IF 钢,分析了 IF 钢脱碳的热力学和动力学条件,阐述了进一步降低成品碳采取的对策措施和达到的效果,为大批量生产极低碳钢提供指导。
3.
The Reduction partition has effect important in two-time cold rolling on Drawability of IF steel,because reduction has effect in cold rolling on {111}texture.
IF 钢的冷轧压下率分配对深冲性能有重要的影响,是由于冷轧过程的压下率对(111)织构的形成有影响。
参考词条
补充资料：叠梁闸门
叠梁闸门
stop log gate
根插入门槽以封闭水道孔口的闸门，也称插板(见图)。制造叠梁闸门的材料有木材、钢材和钢筋混凝土等，目前多半用在中小型水工建筑物上作为检修闸门。叠梁闸门构造简单，制作方便，但接缝较多，漏水量较大，操作也较麻烦。20世纪70年代发展了一种浮式叠梁闸门，是四周密封的箱形梁，可利用浮力减少门重，在水面上利用挂钩梁操作，较为方便。(夏念凌)叠梁闸门d ieliang zhamen叠梁闸门(stop109 gate)由若干根独立的横梁逐
说明：补充资料仅用于学习参考，请勿用于其它任何用途。