1) NiCrWTi alloy film
NiCrWTi合金涂层
2) alloy coating
合金涂层
1.
Based on the technology of Co-B and Co-P alloys nanocrystalline coatings, the ternary Co-Ni-B and Co-Ni-P nanocrystalline alloy coatings were obtained, and the deposit rate and microstructure of ternary nanocrystalline alloys were investigated.
在化学沉积钴硼、钴磷合金纳米晶涂层制备工艺的基础上,制备了钴镍硼、钴镍磷纳米晶合金涂层,研究了三元纳米晶合金的沉积速率和显微组织结构。
2.
Results showed that satisfactory alloyed layer could be also formed on steel castings without adding fusing agent into alloy coating.
研究表明,合金涂层中不加熔剂也能形成质量较好的合金层;铸型中合金膏块相对厚度是决定铸件表面合金层厚度的主要因素;浇注温度提高,合金颗粒适当增大,有利于增加合金层厚度;铸钢合金层的耐激冷激热性能好。
3.
The Ni-based alloy coating and Ni-clad WC ceramic coating were prepared and characterized by abrasive wear resistance test.
对镍基合金涂层和Ni/WC陶瓷涂层进行耐磨实验,结果表明:两种涂层存在不同的磨损特性,WC陶瓷颗粒在涂层及其表面的均匀分布可提高涂层的耐磨性,硬度和韧性的相互匹配是提高材料耐磨性的有效方法。
3) pseudo alloy coating
伪合金涂层
1.
The result shows that compared with pseudo alloy coatings,low-carbon martensite coating presents superior mechanical,anti-wear and machining properties which can be applied to engine components remanufacturing like crankshaft etc.
实验结果表明,与伪合金涂层相比,低碳马氏体涂层呈现出更优异的力学性能、耐磨性能和机械加工性能。
2.
Effects of heat treatments on structure and properties of Mg-A1 Pseudo Alloy Coatings were studied.
本文采用电弧喷涂技术在6061铝合金基材表面制备纯铝涂层,并采用环氧树脂封孔;采用镁铝异质丝材电弧喷涂制备了四种不同镁含量的Mg-Al伪合金涂层,并对涂层进行热处理和环氧树脂封孔。
4) NiCrBSi alloy coating
NiCrBSi合金涂层
1.
In virtue of electron energy spectrometer, X-ray diffractometer and scanning electron microscope, the effects of rare earth yttrium on chemical composition and structure of the vacuum fusion sintering NiCrBSi alloy coating were studied.
利用电子能谱仪、X射线衍射仪、扫描电子显微镜等研究了稀土Y对真空熔结NiCrBSi合金涂层化学组成和组织结构的影响。
5) 316L alloy coating
316L合金涂层
1.
A 316L alloy coating was prepared by high velocity oxygen fuel thermal spraying technique (HVOF) on A3 carbon steel.
利用超音速热喷涂技术在碳钢基体上制备出了 316L合金涂层 ,研究了该涂层在实际炼油环境中的冲蚀行为。
补充资料：氟碳涂层铝合金装饰板制成的铝合金幕墙建筑物
氟碳涂层铝合金装饰板制成的铝合金幕墙建筑物
J氟碳涂层铝合金装饰板制成的铝合金幕墙建筑物
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条