1) upsetting instructions
镦粗规则
1.
Research and application of upsetting instructions during cold forming;
冷锻过程局部镦粗规则的研究及应用
2.
In the absence of systematic upsetting instructions, we would waste quite a few materials as well as a great deal of time for model experimenting.
如果缺少系统的局部镦粗规则的指导,则会造成大量的试模时间和材料的浪费。
2) upsetting
[英][ʌp'setɪŋ] [美][ʌp'sɛtɪŋ]
镦粗
1.
Methods and FE Simulation of Improving Quality of Upsetting;
提高自由镦粗成形质量的工艺方法与有限元模拟
2.
Compare and Analyse of Unit Deforming Force and Boundary Conditions in Model Element of Cylinder Upsetting;
圆柱体镦粗模型单元单位变形力及边界条件的比较分析
3.
Study on the law of temperature influence on brass upsetting microforming;
温度对黄铜微成形镦粗的影响规律研究
3) upset
[英][ʌp'set] [美][ʌp'sɛt]
镦粗
1.
Engineering application of the upsetting straight thread bar’s connection technique;
钢筋镦粗直螺纹技术在工程中的应用
2.
Effect of annealing temperature on microstructure and transverse ductility of upset pure Mo bars
退火温度对镦粗纯钼棒组织和横向塑性的影响
3.
The deformation extent of metal decreases from top to bottom along longitude direction during upset and changes into cylinder,accumulating deformation exists during processing,the shape phenomenon is not observed and the ove.
研究表明,正挤压时,金属在模腔中延伸变形成圆台体,受模具形状影响,变形程度从顶端向底端逐渐减小;圆台体镦粗时金属在高度方向从顶端至底端各层沿径向流动逐渐减小,依次连续变形成圆柱体。
4) roughness of rule
规则粗糙度
5) rough rules set
粗糙规则集
1.
With uncertain measurement of rough rules set, relative attribute reduction is obtained by applying GA, and then rough rules set is deduced under the threshold values.
通过粗糙规则集的不确定性量度 ,应用遗传算法求取相对属性约简 ,然后根据所给阈值导出粗糙规则集 ,并对阈值对规则集的影响进行了事后分析 。
6) powder upsetting
粉末镦粗
补充资料:自动冷镦机、多工位螺栓自动冷镦机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
(一)加工精度 | 参照GB9166-88、JB/T3053-91 | ||||||
1、冲头夹持器模孔中心线对夹持器后支承面的垂直度(mm) 在100长度上 | 0.008 | 0.01 | 0.015 | >0.015 | |||
2、凹模座模孔中心线对凹模后座支承面的垂直度(mm) 在100长度上 | 0.008 | 0.01 | 0.015 | >0.015 | |||
3、冲头夹持器模孔中心线对滑块行程的平行度(mm) 在100行程上 | 0.016 | 0.02 | 0.02 | >0.02 | |||
4、滑块行程对机身上与凹模座贴合的垂直面的垂直度(mm) 在100行程上 | 0.016 | 0.02 | 0.02 | >0.02 | |||
5、工件头部对工件杆部中心线的偏移量(mm) | <0.20 | 0.20~0.25 | 0.25~0.30 | >0.30 | |||
(二)生产率(件/分) | |||||||
20mm | >80 | 70 | 65 | <65 | |||
30mm | >60 | 50 | 45 | <45 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条