1) heating evaporation
热蒸
1.
In this paper, the working principle of heating evaporation is briefly described.
本文简要叙述了真空热蒸发的原理,并通过热蒸发用有机物来在线包覆铜纳米粉末。
2) superheated steam
过热蒸汽
1.
Experimental investigation on production of granular MAP by reaction and drying in a superheated steam fluidized bed;
过热蒸汽流化床制备粒状磷酸一铵的实验研究
2.
Experimental studies on the fly ash ultrafine process with superheated steam;
电厂过热蒸汽制备微细粉煤灰的试验研究
3.
Direct application of superheated steam in the production of caustic soda;
过热蒸汽在烧碱生产中的直接应用
3) steam tracing
蒸汽伴热
1.
It proves that electric tracing is prior to steam tracing.
从技术性能上介绍了蒸汽伴热的缺陷和电伴热的优势，并就某化肥厂７００ｍ长工艺管线保温采用电伴热和蒸汽伴热方式，进行了技术经济分析比较，论证了采用电伴热技术经济上合理，效益显
4) steam heating
蒸汽加热
1.
Energy Saving and Surplus heat use in steam heating system;
蒸汽加热系统节能及余热利用
2.
This paper describes the innovation on hydrogen generator by ammonia decomposition process , electric heating is replaced by steam heating , the vaporizer of ammonia is reconstructed, nitrogen is heated directly by electric heating to make molecular sieve regenerate, purification system is transformed .
改造氨汽化器,用蒸汽加热液氨替换电加热液氨;用电加热器直接加热氮气,使分子筛加热再生,改造净化系统。
3.
This paper analyses the water-film formation in steam heating roller and its influence on heat conduction performance to roller, and then provides a better settlement scheme for the problem of how to eliminate the water-film and improve the heat conduction performance of the roller.
就蒸汽加热辊中水膜的形成、对辊筒的导热性能的影响进行了分析,针对如何消除水膜、提高辊筒导热性能的问题提出了解决方法。
6) thermal evaporation
热蒸发
1.
Growth of ZnO nanowires by free-catalytic thermal evaporation of ZnS powder;
无催化热蒸发ZnS粉末制备半导体ZnO纳米带
2.
Aligned cone-shaped nano-ZnO structure has been synthesized by thermal evaporation of mixtures of Zn powder,C powder and ZnO powder through one step,which overcomes the disadvantage of the previous methods through two steps: preparation catalyst first and then synthesis of nano-ZnO.
将锌粉、炭粉和氧化锌粉末混合,用简单的热蒸发方法一步就合成了大量的尖锥状纳米ZnO阵列,该方法克服了其它制备方法需要先单独制备催化剂再合成ZnO的缺点而且得到产物不含杂质。
3.
Tin oxide nanoshuttle arrays were synthesized by thermal evaporation.
利用热蒸发法在硅衬底上合成了二氧化锡纳米梭阵列,并研究其场致电子发射特性。
补充资料：再热蒸汽系统
再热蒸汽系统
reheating steam system
zolre zhengq一x一tong再热燕汽系统(reheating steam system)汽轮机高压缸的排汽返回锅炉再热器再热后送回汽轮机中压缸的燕汽管道系统。若采用二级再热，则还应包括中压缸排汽再热后返回低压缸的燕汽管道系统。 从汽轮机高压缸(或中压缸)排汽口到锅炉再热器进口的蒸汽管道，称为低温再热蒸汽管道;从再热器出口到中压缸(或低压缸)的燕汽管道，称为高温再热蒸汽管道.低温再热蒸汽温度较低，管道材料通常采用优质碳素钢;高温再热燕汽温度一般与主蒸汽温度相同或略高，管道材料采用耐热合金钢。 燕汽在再热系统中的流动阻力对循环热效率的影响较大，每增加0.1 MPa的流动阻力，循环热效率将降低。.2%~。.3%.增大再热蒸汽管道和再热器的管径，虽可降低再热系统的流动阻力，但增加管道和设备的投资费用。所以，再热燕汽系统(包括锅炉再热器)的流动阻力一般限定在高压缸排汽压力的8纬~10%。 火电厂设计中，为降低再热燕汽管道的投资，通常采用提高高温再热蒸汽管道蒸汽流速的方法来减小管径，以降低耐热合金钢管材的消耗量;高温再热蒸汽管道因减小管径而增加的压力损失，可以用增大低温再热燕汽管道管径以减少压力损失来补偿。再热燕汽系统压力损失给定后，高温再热蒸汽管道和低温再热蒸汽管道的管径应通过优化计算来确定。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条