1) solder alloy
焊接合金
1.
The Sn-Zn,Sn-Zn-Bi,Sn-Zn-Bi-RE and Sn-Zn-Bi-Ag lead-free solder alloy series were prepared in this work.
制备了 Sn-Zn、Sn-Zn-Bi、Sn-Zn-Bi-RE 与 Sn-Zn-Bi-Ag 系无铅焊接合金,研究了合金的熔点、熔化温度区间、对铜板的润湿性、微观结构和电化学性能。
2) brass brazing alloy
黄铜焊接合金<冶>
3) weld
焊接
1.
Research on the welding performance of low-carbon nickel;
低碳镍材料焊接性能的研究
2.
Weld Repair and Maintenance of the Steel Belts in the Rotary Belt Condensation Granulators;
回转带式冷凝造粒机钢带的焊接修复与维护
3.
Cause Analysis of the Weld Flaw Between the Flanges and Internal Sleeves of the High Pressure Heat Exchangers and Countermeasures;
高压换热器法兰与内套焊接裂纹原因分析与对策
4) Welding
焊接
1.
The Research Development of Finite Element Simulation in Welding Joint;
焊接接头有限元模拟的研究进展
2.
On Welding of Stainless Steel Compound Plate 16MnR+00Cr19Ni10;
16MnR+00Cr19Ni10不锈钢复合钢板的焊接
3.
Heat source model for 2D welding temperature field simulation based on the configuration of welding line;
基于焊缝形状的二维焊接温度场模拟热源模型
5) jointing
焊接
1.
Application of ultrasonic jointing principle in needle destruction device;
超声波焊接原理在注射针头销毁器中的应用
2.
Quality control in the process of assembling and jointing have interrupted francis turbine at Lijiaxia Hydropower Station;
李家峡水电站混流式水轮机分瓣转轮组合与焊接过程中的质量控制
3.
This paper introduces the jointing method to recover the crushing equipment cone crusher whose axes are broken in two parts.
介绍了大型破碎设备圆锥破碎机主轴断裂后的焊接修复方法。
6) Welded joint
焊接
1.
Prediction system of CTOD for high strength pipeline steel welded joint based on back propagation artificial neural network;
基于BP人工神经网络的高强度管线钢焊接接头性能参数CTOD预测系统
2.
Corrosion characteristics of welded joints of copper pipe in seawater;
紫铜海水管焊接部位在海水中的腐蚀特征
3.
Corrosion behavior of welded joints of copper pipe in artificial seawater;
紫铜海水管焊接部位在人工海水中的腐蚀行为
参考词条
补充资料：可焊接铸造铝合金
可焊接铸造铝合金
weldable cast aluminium alloy
kehanjie zhuzao IUhejin可焊接铸造铝合金(weldable cast alumini-um alfoy)以焊接性能为主要指标的铸造铭合金，一般同时具有良好的气密性和强度，用于焊接结构。铸造铝合金的焊接性能主要取决于化学成分。全吕-硅系合金有优良的焊接性能，在焊接凝固时，由于铝-硅合金的收缩率小，几乎不产生裂纹。镁、铜含量多的合金焊接性能不佳，含量越高则焊接越困难。合金中加入锰有利于焊接。具有良好焊接性能的铸造铝合金有:ZLlol(AI一6.5%一7.5%51一0.25%一0.45%Mg)，ZLIOZ(AI一10%一13%51)，ZLlo3(AI一4.5%~6.0%Si一1 .5%一3.0%Cu一0.3%~0.7%Mg一。.2%~。.6%Mn)，21才106(Al一7.0%一8.5%51一1.0%心1.5%Cu-0 .3%一0.5%Mg一0.3%一O:5%Mn)， ZLlll(Al-8 .0%一1 1.0%51一1.3%一1.8%Cu一0.4%一。，6%Mg-o·1%一O·35%Mn一0.2%~0.5肠Ti)等合金。 含有镁的铝一硅系ZL101合金，在相组成中除铝和硅的共晶体外，有少量的MgZsi强化相，可热处理强化。当硅含量取上限时，经淬火人工时效，抗拉强度可达30OMPa，伸长率大于5%，有良好的焊接性能和耐蚀性，可用于制造中等强度负荷的零件。 含铜量高的ZL103合金，在组织中有CuAI:和Mgzsi相，可热处理强化，具有高的强度和耐热性，焊接性能合格，可用于制造耐热中强负荷的焊接零件。 (朱耀明)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。