2) blind hole sleeve parts
盲孔套筒零件
3) parts with deep hole
深孔类零件
1.
This article describes the method that flow plating out of groove is used to restore parts with deep holes after the parts′ inner surface abrasion.
阐述了对各种深孔类零件内表面磨损以后进行槽外流镀的方法 ,克服了大件及无法绝缘件的镀铁困难问题 ,并确定了最佳工艺过
4) components with holes
孔类零部件
1.
To cater to the demands of the engine casing in dynamic analysis and modeling erection,the typical structures such as supporting casing,components with holes and engine components are discussed for model predigesting.
从计算航空发动机机匣系统动力特性需要以及有限元模型建立的角度出发,研究了支承及非支承机匣系统中空心幅板类零部件、孔类零部件、附件等典型结构在整机建模中结构简化的处理方法,分析了某涡扇发动机整机动力特性。
5) multihole parts
多孔类零件
1.
This paper puts forward the frame construction of an automatic programming system in connection with the numerical machining complexity demands of multihole parts,and researches into the key techniques of the system.
针对多孔类零件数控加工的工艺复杂性,提出了基于CATIA的自动编程系统框架结构,并对其关键技术进行了研究。
6) Parts with blind holes
盲孔件
补充资料：机械类常用英语：冲压模具-零件类
punch冲头
insert入块(嵌入件)
deburring punch压毛边冲子
groove punch压线冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location
定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆
trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子
ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
sliding dowel block滑块固定块
active plate活动板
lower sliding plate下滑块板
upper holder block上压块
upper mid plate上中间板
spring box弹簧箱
spring-box eject-rod弹簧箱顶杆
spring-box eject-plate弹簧箱顶板
bushing bolck衬套
cover plate盖板
guide pad导料块
insert入块(嵌入件)
deburring punch压毛边冲子
groove punch压线冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location
定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆
trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子
ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
sliding dowel block滑块固定块
active plate活动板
lower sliding plate下滑块板
upper holder block上压块
upper mid plate上中间板
spring box弹簧箱
spring-box eject-rod弹簧箱顶杆
spring-box eject-plate弹簧箱顶板
bushing bolck衬套
cover plate盖板
guide pad导料块
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条