2) laser spot welding
激光点焊
1.
In this paper, laser spot welding was used to join a NdFeB permanent magnet to an SPCC (steel plate cold commercial) steel in an effort to achieve joining of magnet/steel dissimilar materials with high speed and quality, with the joint formation mechanism, hardness, strength, and fracture behavior analyz.
为实现钢磁异质材料之间快速和高质量的连接,该文探索采用激光点焊方法连接SPCC(steel plate cold commercial)钢与NdFeB永磁体,并对接头的形成过程、硬度、强度和断裂行为进行了研究。
2.
However, laser spot welding of aluminum has some problems, such as instability, porosity, crack, crater, and low tensile strength.
激光点焊具有高精度,高效率等特点,在航空航天工业中有望替代传统的电阻点焊和铆接等连接方法。
3.
In the field of laser processing, laser spot welding technology gradually becomes the focus of people s attention for its high-precision and high-efficiency, as a new type technology.
在激光加工领域,激光点焊技术是一种新型的技术,具有高精度,高效率等特点,逐渐成为人们关注的焦点。
3) Laser welding
激光焊接
1.
Porosity prevention of 1420 Al-Li alloy for laser welding;
1420铝锂合金激光焊接气孔抑制技术
2.
State-of-arts of visual sensing technology to monitor laser welding process;
激光焊接过程视觉传感技术的发展现状
3.
Study on the twin-focus technique in laser welding;
激光焊接中的双焦点技术
4) laser weld
激光焊接
1.
The mechanical properties,microstructure and micro-hardness of laser welded joint were researched.
对抗拉强度600 MPa级的低碳相变诱发塑性钢(TRIP钢)进行了拉伸、成形、高速冲击拉伸和激光焊接试验。
2.
During the laser welding stainless steel 304 with deep penetration,it reasearches the relationship between laser tchnique and seam shape based on the method of secondary general rotary regression design.
在304不锈钢的激光深熔焊中,通过工艺试验,研究了激光焊接工艺参数与焊缝形状参数之间的关系。
3.
This paper introduces the current status and several important points of the development activities at the Vehicle Structure Technology Division,RTRI,such as evaluation of strength of laser weld in car body structure,double action rubber draft gear with damping devices,researches on the suppression of flexural vibration of car body,studies to suppress vertical vibration o.
文章针对不锈钢制车体激光焊接区的强度评价法、复动式车钩缓冲器、减轻车体挠曲振动方法、带轴减振器的车体减振系统以及不锈钢车体的碰撞安全性等5个专题,介绍了车辆结构技术研究部的研究成果,阐述了技术发展动向。
5) laser beam welding
激光焊接
1.
Microstructure and properties of joints of wrought magnesium alloy AM60 plates welded by laser beam welding;
AM60变形镁合金薄板激光焊接接头的组织与性能
2.
Process instability in laser beam welding of 5083 aluminium alloy for shipbuilding;
5083船用铝合金激光焊接不稳定性研究
3.
Study on the weldability of the quenched and tempered 30CrMnSiA with laser beam welding;
30CrMnSiA调质钢的激光焊接性研究
6) YAG laser welding
YAG激光焊接
1.
In this paper, pulse YAG laser welding of stainless steel string with weak - magnetism, constant -elasticity (φ= 0.
5mm,φ=5mm)的脉冲YAG激光焊接,进行了焊缝形貌、金相、成份分析,测试了接头强度,计算了焊点的熔合比及能量利用率。
2.
Dynamic process and spectral distribution of vapor/plasmas during YAG laser welding of 5A90 Al-Li alloy were obtained by high-speed camera and spectra measure system.
利用光谱测量、高速摄像等手段,对5A90铝锂合金YAG激光焊接过程中的金属蒸汽/等离子体的动态变化过程、光谱分布测量和计算表明:5A90激光焊接时金属蒸汽/等离子体几乎只从熔池正面喷出,主要强谱线为Li670。
补充资料：闭式单点、双点压力机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
（一）加工精度 | 参照GB10924-89、GB10933-89、JB5200-91 | ||||||
1、滑块下平面对工作台上平面的平行度（mm） | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.02+0.10/100×滑块下平面的被测长度 | |||||||
2、滑块行程对工作台上平面的垂直度 | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.05+0.02/100×滑块行程长度 | |||||||
（二）结构性能 | |||||||
1、离合器、制动器接通率，当滑块行程次数≤16次/分时为70%，≤25次/分时为60%，≤45次/分时为50% | 大于规定值10% | 大于规定值 | 达到规定值 | 达不到规定值 | |||
2、液压超负荷保险装置、微调装置、吨位指示器 | 全部具有 | 全部具有 | 部分具有 | 没有 | |||
（三）噪声dB（A） | |||||||
1、公称力≤400kN | ≤85 | ≤87 | ≤88 | ＞88 | |||
2、公称力＞400kN | ≤87 | ≤88 | ≤90 | ＞90 | |||
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条