2) bias voltage
偏置电压
1.
Experimental Study on Influence of Interference and Bias Voltage on Detective Signal of Spark Plug;
干扰及偏置电压对火花塞检测信号影响的试验研究
2.
The influences of the bias voltage and hydrostatic pressure on FE/AFE and AFE/PE phase transition and transition temperature of these PLZST ceramics obtained by measuring the relation between the relative dielectric constants and loss and various parameters of samples.
通过测定样品的相对介电常数及损耗与各种参量的关系,得到了等静压力及偏置电压对反铁电体铁电/反铁电相变及反铁电/顺电(PE)相变温度影响的规律。
3.
The bias voltage Vp was discussed.
直流偏置电压V_p可消除系统倍频振动,为后续检测电路设计提供便利。
3) biased voltage
偏置电压
1.
The uniformity and conformity of the oxidation lines of Si obtained by AFM (atom force microscope) tip induced oxidation ofdifferent biased voltages and scanning speeds are studied.
研究了在不同的偏置电压和扫描速度下加工的Si氧化线的一致性和均匀性,得到了加工高质量的Si氧化线的实验条件为:偏置电压8V,扫描速度1 μm/s。
2.
Ti oxidation lines with 5 μm length were fabricated at temperature of 20 ℃,relative humidity of 30 %,oxygen concentration of 20 %,and different biased voltages and scanning speeds.
偏置电压和扫描速度是AFM阳极氧化加工Ti纳米氧化线的决定因素。
4) bias current
偏置电流
1.
Under normal operation state,the load of the three-phase full-controlled rectifier is an impedance;under fault state,the load becomes an impedance plus even frequency reverse electromotive force due to the even frequency reverse electromotive force generated in the FCL dc bias coil,the dc bias current includes the dc component and even.
为提高偏置电流系统的控制精度,设计了一种运用模糊PID在线修改控制器参数的新型偏置电流控制系统。
2.
The effect of bias current on the performanc e of active magnetic beari ng(AMB)is studied in this paper.
研究了电磁轴承偏置电流对其性能的影响 ,给出了电磁轴承电磁设计的基本原则和基本步骤 ,将电磁轴承的设计分成两个步骤 ,即不考虑铁心磁阻的初始设计和考虑铁心磁阻的校算设计 。
3.
The paper carried out the reasoning of the formula which implies the relationship between optical modulation depth and the input level of a optical transmitter and the formula implied between single channel modulation depth and bestir level & bias current.
推导出光调制度与光发射机输入电平的关系算式、激励电平与激光器偏置电流和单频道调制度的关系算式,分析系统频道数变化对调制度恒定型光发射机激励电平的影响规律,同时分析常见光发射机标称输入电平的标示方式、结构特点和具体应用调试方法。
5) partially installing capacitor
偏置电容
1.
Application experiences of capacitive current measuring with partially installing capacitor;
偏置电容法电容电流测量的应用经验
2.
According to above analysis, a new more safe and more portable method which adapts to field test is putted forwards, that method is partially installing capacitor.
根据几个变电站电容电流的测试情况和在华北电力大学试验室的模拟试验情况,对3种间接测试方法和1种直接接地方法进行比较,提出了一种适合于现场测试、既安全又简便的测试方法——偏置电容法,并介绍了其测量原理和注意事项。
6) bias circuit
偏置电路
1.
This paper proposes a bias circuit for cascode current mirror in band-gap voltage reference to realize low supply voltage.
通过设计带隙基准电压源中共源共栅电流镜的偏置电路以实现低电源电压工作。
2.
The physical performance can be understood explicitly in the equivalent networks,and the judgement of stability functions of every bias circuit could be simply gained.
本文给出了求出典型放大器偏置电路的戴维南等效电路,依此等效电路可直接看清电路工作时的物理意义,进一步判定各个放大电路静态工作点稳定性能的优劣。
3.
This paper analyses the quiescent point Q of base electrod potentiometer bias circuit which is evaluted by method of traditional double batteries,and gives a condition which is engineering approximately estimate quiescent point Q of base electrode potentiometer bias circuit.
本文通过传统的双电池法对基极分压式偏置电路静态工作点Q求解过程的分析,给出了工程估算法估算基极分压式偏置电路静态工作点Q的条件。
补充资料：偏置屈服应力
分子式：
CAS号：
性质：应力-应变曲线偏离线性达到规定应变百分数的应力。也有称作残余变形屈服应力。该规定的变形量是人们事先商定的（偏置）。这种场合往往是由于该材料的应力、应变曲线不出现明显的屈服点，故作此规定。以统一衡量材料的力学性能，便于互相比较。当然，规定的该值不应超过该材料的拉伸强度值。
CAS号：
性质：应力-应变曲线偏离线性达到规定应变百分数的应力。也有称作残余变形屈服应力。该规定的变形量是人们事先商定的（偏置）。这种场合往往是由于该材料的应力、应变曲线不出现明显的屈服点，故作此规定。以统一衡量材料的力学性能，便于互相比较。当然，规定的该值不应超过该材料的拉伸强度值。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条