1) adiabatic shear fracture
绝热剪切断裂
2) adiabatic shear
绝热剪切
1.
Effect of several deformation mode on microstructure performance and adiabatic shear sensitivity of tungsten heavy alloy;
几种变形方式对钨合金组织性能及绝热剪切敏感性的影响
2.
These reviews include three search fields: the equipment of electromagnetic riveting,the process of electromagnetic riveting and the deformation mechanism of adiabatic shear: the low voltage electromagnetic riveter is in the works and the simulation of electromagnetic riveting will be more and more importance in the analysis.
从原理出发,对国内外电磁铆接设备、工艺及绝热剪切变形机理的研究进行了分析比较,指出电磁铆接设备将走低电压发展的道路,数值模拟将在今后的研究中发挥越来越重要的作用,最后对该领域的发展趋势提出自己的观点。
3.
By analyzing SEM photo of the chip in turn-milling,it is found that adiabatic shear take place inside the chip.
分析了正交车铣切屑的扫描电子显微镜的照片,发现有绝热剪切发生,证明正交车铣锯齿形切屑产生的原因是切屑内部的局部产生突变性剪切所造成的。
3) Adiabatic Shearing
绝热剪切
1.
Effects of Deformation on Microstructure Performance and Adiabatic Shearing Sensitivity of Tungsten Heavy Alloy;
变形对钨合金微观组织性能及绝热剪切敏感性的影响
2.
Numerical simulation on adiabatic shearing behavior of TB2;
TB2钛合金绝热剪切行为的数值模拟
3.
So, only in 93W, the adiabatic shearing bands can be found.
通过对比发现 ,二者的断裂机理基本相似 ,但侵彻时 ,由于 90W钨合金中存在较多的粘结相而使得其蘑菇头较小 ,其中的钨颗粒变形也较小 ;只在 93W钨合金中发现了绝热剪切现象的征
4) adiabatic shear band
绝热剪切
1.
Although the void damage with adiabatic shear band has been observed in experiments, and the thermal softening effect has been discussed extensively in literature, there is very little research on its damage effect.
绝热剪切破坏是冲击载荷作用下金属材料中经常出现的一种重要破坏模式 ,尽管已经在实验中观察到了绝热剪切带内部的损伤现象 ,但是在理论和计算模型中往往还只是考虑它的热软化效应 ,对与之伴随的损伤破坏效应却鲜有讨论 。
2.
The dynamic mechanical properties and susceptibility to adiabatic shear band (ASB) of the tungsten heavy alloy (WHA) deformed by the HE&CT were systematically investigated.
35Co 钨合金进行热挤压变形强化,获得纤维组织,再通过冷扭转变形调整纤维状钨颗粒的取向,对压、扭复合工艺制备的钨合金进行动态压缩性能测试和绝热剪切敏感性的分析,并与烧结态和冷扭转态钨合金作对比研究。
3.
The dynamic flow stress-loading time curves as well as the metallurgical analysis of adiabatic shear band show that localized adiabatic shear deformation happened in both TC4 and DT4,however this process is so transient for titanium alloy TC4 that it takes only several microseconds,but it takes most of the loading time for electromagnetic iron DT4.
采用分离式Hopkinson压杆装置对TC4钛合金和DT4电磁纯铁的帽形试样进行动态冲击实验,以研究两种材料高应变率下的绝热剪切行为,并分析材料热物理性能和力学性能对其绝热剪切敏感性的影响。
5) shear fracture
剪切断裂
1.
The fragment ratio of tension and shear fracture of 50SiMnVB cylinder shell under explosive load is investigated.
试验中还观察到在拉伸断口应力方向的断面上出现了熔化现象,这说明在拉伸断裂区局部存在着剪切现象,同时证明采用高能束改性后圆筒在爆炸载荷作用下可产生全壁厚剪切断裂。
2.
A macro and micro and chemical element analysis was made on fracture of ruptured coupling bolts,torsion test was performed and stress analysis and calculation were made,the results show that when the steam turbine had failure,MP-LP rotor coupling bolts and generator-exciter rotor coupling bolts failure were classified as overload shear fracture with partial deformation .
对215MW汽轮机断裂的对轮螺栓做断口宏观、微观分析,化学元素分析,扭转试验及受力分析计算,结果表明汽轮机组在事故中,中压-低压转子对轮螺栓和发电机-励磁机转子对轮螺柱的失效类型为:过载剪切断裂,同时局部挤压变形,这是由于事故过程中轴系受到冲击扭矩作用而引起的。
3.
Extensive research has been done on the fracture behavior of concrete, but very little on shear fracture.
有关混凝土的断裂行为己被广泛研究,但很少是针对剪切断裂的情况。
6) sheer fracture
剪切断裂
1.
Experiment study on size effect of concrete sheer fracture;
混凝土剪切断裂的尺寸效应试验研究
补充资料：剪切断裂
分子式：
CAS号：
性质：又称剪切断裂。有明显塑性变形的断裂。断面呈暗纤维状，断口表面与受力方向或45 角。当容器承受的压力超过设计压力达到材料的屈服极限时，容器开始变形，容器直径增大、壁厚减小，达到不稳定状态后，容器局部塑性变形骤增，破裂失效。
CAS号：
性质：又称剪切断裂。有明显塑性变形的断裂。断面呈暗纤维状，断口表面与受力方向或45 角。当容器承受的压力超过设计压力达到材料的屈服极限时，容器开始变形，容器直径增大、壁厚减小，达到不稳定状态后，容器局部塑性变形骤增，破裂失效。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条