|
|
1) Compress profile
压缩剖面
2) pressure profile
压力剖面
1.
In this paper, pressure profile adjustment technique for multi-layer and multiple pressure system reservoir in adjustment well drilling block during the process of drilling is studied.
本文针对调整井钻井区块多层系多压力系统储层在钻井施工过程中压力剖面调整技术展开研究。
2.
The pressure profile adjustment reduces the high-pressured lamination strength, maintains the low-pressure lamination strength, realizes reduces to the oil layer pollution, reduces the drilling cost based on the existing oil-field development plan.
压力剖面调整是在现有的油田开发方案基础上,降低高压层压力,保持低压层压力,实现减轻对油层污染、降低钻井成本。
3) pressure drawdown profile
压降剖面
1.
Aimed to the different flow rate contribution problem caused by pressure drawdown at the hell segment in horizontal well,a calculation model of pressure drawdown profile was proposed based on the Z.
结果表明:利用尾管技术能有效地改善水平生产井段的流体压降剖面和流量剖面;对于一定的水平生产井段,存在最佳的尾管长度和尾管直径,算例中,最佳的尾管长度约为水平生产井段长度的3/10,最佳尾管直径约为0。
4) dynamic pressure planning
动压剖面
1.
An analytic trajectory solution based on dynamic pressure planning is presented for the gliding reentry of lift-body.
针对升力体飞行器滑翔再入的飞行特点,提出基于动压剖面的再入弹道解析方法。
5) cross-section shortening amount
剖面缩短量
6) m expansion or contraction
等伸缩剖面
补充资料：关于solidworks 中的剖面线中的剖面线
solidworks的剖面线线型定义和autocad相同,它使用了autocad的剖面线定义方法,与autocad通用.因此,可以对剖面线进行定义. 方法:修改\SolidWorks\lang\chinese-simplified\sldwks.prn 用笔记本打开该文件,添加需要的线形.如 ;; Based on AutoCAD Ver.13.0s Hatch Pattern File ;;;; solidworks 区域剖面线定义文件 :: *金属, (Iron BrickStone), ANSI Iron, Brick, Stone masonry 45, 0,0, 0,.125 *塑料, (Lead Zinc Mg), ANSI Lead, Zinc, Magnesium, Sound/Heat/Elec Insulation 45, 0,0, 0,.125 135, 0,0, 0,.125 *玻璃,AR-GLASS@1.0 45,0,0,0,0.5, 0.5,-0.5 45,0,0.1414214, 0,0.5, 0.3,-0.7 45,0.1414214,0, 0,0.5, 0.3,-0.7 *软木, Cork material@1.0 0, 0,0, 0,.125 135, .0625,-.0625, 0,.35355339, .176776696,-.176776696 135, .09375,-.0625, 0,.35355339, .176776696,-.176776696 135, .125,-.0625, 0,.35355339, .176776696,-.176776696 *无, None 删除不需要的定义类型,可以大大提高solidworks 的启动速度
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条
|