1) Path Test Data
![点击朗读](/dictall/images/read.gif)
路径测试数据
1.
The method of program insert is integrated with AGA to implement the automatic generating of path test data.
通过把程序插装法与该遗传算法相结合,实现了路径测试数据的自动生成。
3) path testing
![点击朗读](/dictall/images/read.gif)
路径测试
1.
On Program Testability Based on Path Testing;
![点击朗读](/dictall/images/read.gif)
基于路径测试的程序可测试性研究
2.
This paper focuses on automatic test data generation for path testing using genetic alg.
![点击朗读](/dictall/images/read.gif)
本文主要研究的是路径测试数据的自动生成方法。
3.
This paper focuses on automatic test data generation for path testing using genetic algorithms.
本文主要对面向软件测试中路径测试的数据自动生成方法进行研究。
4) path coverage test
![点击朗读](/dictall/images/read.gif)
路径测试
1.
In accordance with the characteristics of path coverage test and the graph theory,this paper presents a new program control flow diagram model.
针对路径测试的特点,结合图论的知识,提出了控制流程图的一种表示方法。
2.
In accordance with the characteristics and coverage requirement of path coverage test as well as the graph theory,this paper presents a new program control flow diagram model.
针对路径测试的要求及其特点,结合图论的概念,提出了程序控制流程图的一种表示方法。
5) test path
![点击朗读](/dictall/images/read.gif)
测试路径
1.
The test paths of an example to satisfy each testing criteria are listed in a table.
![点击朗读](/dictall/images/read.gif)
然后通过例子,给出了基于各个标准产生的测试路径,最后给出了结论以及下一步应考虑的问题。
2.
Focusing on the problem of infinite paths created by the events for GUI,the author presented a test path generation approach for GUI based on event weight in an event-flow graph(EFG).
针对GUI事件驱动特性产生无限多个测试路径的问题,提出在事件流图中考虑事件权重的GUI测试路径生成方法。
6) path test
![点击朗读](/dictall/images/read.gif)
路径测试
1.
Study on Automatic Generating Path Test Data Based on PSO;
![点击朗读](/dictall/images/read.gif)
基于PSO的路径测试数据自动生成方法研究
补充资料:测试数据处理
测试数据处理
data processing of testing results
eeshi shuju ehul:测试数据处理(data proeess庄ng of testingresults)在选矿测试技术中,对测试的信号要进行加工处理,包括完成滤波处理,工程量变换,线性化处理,标准化处理(包括定标,死时间校正,漂移校正,标准化系数校正,测量值上、下限检验等),再经过测试仅器标定,把仪器测得的表观值变为实际值;对于动态测量还包括数据的采取,检验和取舍,转换,预处理以及确定动态特性指标,数学模型等。数据处理内容有计算测量精度、测量平均值,求出标准偏差;必要时进行组合测量;最终对所得实际值进行误差分析和统计检验。从狭义说,测试数据处理仅指此最终过程。在现代自动测试系统中,数据采集和处理均由计算机系统控制,包括自动完成最终数据的分析检验;输出的信息可满足显示、打印或记录、贮存、控制等要求。 测量精度被测对象多为样品而非总体,而且测试中必有误差,即测试得不到被测参量真值,必须根据误差理论对所得结果的可能彼动范围作出一区间的估计,并指出这种估计的可靠程度。用仪表测得的被测参量的测得值和其真值的接近程度为测量精度,二者之间的差即为测量误差。测量误差包括粗大误差、系统误差和随机误差。 测量平均值由数理统计证明,通过有限的N次 等精度测量,所得的测得值x、的 算术平均值 N 王一责馨二、 为该被测参量的真值的无偏估 计。 标准偏差工程测量的随机 误差绝大部分都近似地符合正态 分布,由此可求出测量的标准偏差 ;*一德 式中次为测量残差,民一x*一王。可 A 以按照次妻3。的原则,剔除测量中 的粗大误差;对于系统误差除可根 据民值的规律性判断是否存在 外,有时还须通过统计检验方可查明;要寻找出系统误差存在的原因,并设法消除或修正。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条