1) Bifurcation Adjustment
分叉点调整
2) cross regulation
交叉调整
1.
Passive solution to improve cross regulation of multi-output SMPS;
改善多路输出开关电源交叉调整率的无源设计方法
3) yoke adjusting kit
叉臂[离合器分离叉]调整工具包
4) cross regulation
交叉调整率
1.
Transformer is a key component to improve cross regulation of multiple-output flyback converter.
鉴于变压器性能对多路输出反激变换器的交叉调整率有重要影响,为变换器的关键器件之一,提出了基于有限元数值仿真的任意多路输出变压器的建模方法。
2.
Magamp is an effective solution for improving cross regulation of multi-output power converter.
磁放大器后级稳压技术广泛应用于改善多路输出功率变换器的交叉调整率。
5) adjustment yoke bracket
调整叉臂架
6) bifurcation point
分叉点
1.
Based on mechanical calculation model of sheet slope crack, the regions nearby equilibrium bifurcation point and evolutions along equilibrium path were investigated by analyzing the buckling behavior and deformation factors of side slopes .
应用板裂边坡介质力学计算模型,在边坡岩体屈曲性态和变形因素分析的基础上,研究了层状边坡在分叉点附近的邻域,探讨了结构分叉后平衡路径的演化途径;应用后屈曲能量准则建立的平衡稳定模态幅值方程,充分考虑屈曲岩层自重的法向分力对边坡稳定性的影响,得到一般情况下板裂介质岩体边坡溃屈极限长度方程;给出了任意倾斜角度边坡溃屈极限长度和模态幅值的极值,并以此作为岩体边坡稳定性的位移判剧。
2.
Nearby region at bifurcation point of rock mass slope is derived;the stability criteria of side slope relating to equilibrium path of post-buckling,equilibrium configuration of bifurcation point and post-buckling are established in the form of general side slope.
给出了边坡岩体分叉点附近的邻域,建立了一般情形下边坡岩体分叉点的平衡构形判据,以及后屈曲平衡路径和后屈曲平衡构形的稳点性准则。
3.
In accordance with deformed specifities of all kinds of bedding rock slope,this paper studied the regions nearby equilibrium bifurcation point, limit lengths of slope buckling failure and evolutions along equilibrium path by using modality amplitude equation of equilibrium stability built on post-buckling energy criterion.
应用后屈曲能量准则建立的平衡稳定模态幅值方程,研究了不同类型层状边坡在分叉点附近的邻域及其溃屈极限长度,探讨了结构分叉后平衡路径的演化途径。
补充资料：三叉点
三叉点
〖HT5”SS〗triradius
又称“纹三射。”指纹或趾纹的基本纹型与其周围的纹理可以发生交汇，交汇中央似一开口的三角形，三方均有纹理向外辐射，称为纹三射(或称三幅线、三叉、三角）。弓形纹无纹三射，箕形纹有一个三叉(纹三射），斗形纹有二个三叉(纹三射）。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条