1) IGBT inverter failure
![点击朗读](/dictall/images/read.gif)
IGBT逆变器故障
2) IGBT inverter
![点击朗读](/dictall/images/read.gif)
IGBT逆变器
1.
The paper presents in the end the simulation model of IGBT inverter.
![点击朗读](/dictall/images/read.gif)
通过对逆变器中的直通电流问题的论述,提出了检测直通电流的几种方案,以IGBT逆变器为例,给出了检测直通电流的仿真模型。
2.
The converter is composed by thyrister rectifier and IGBT inverter,and uses a PWM rectifier as a load to control output current.
辅助电源变流系统由晶闸管整流器和被测IGBT逆变器组成,负载采用PWM整流器控制输出电流。
3.
A higher-voltage ,low-switching frequency IGBT inverter and a lower-voltage, high-switching frequency MOSFET inerter are used in the combination to achieve harmonic current compensation.
IGBT逆变器的作用是提供基波电压,并补偿无功功率,MOSFET逆变器则实现消除谐波电流的功能。
3) IGBT arc welding converter
![点击朗读](/dictall/images/read.gif)
IGBT弧焊逆变器
4) IGBT traction inverter
![点击朗读](/dictall/images/read.gif)
IGBT牵引逆变器
1.
This paper introduces the main parameters, power circuit and general structure of the DC 1 500 V IGBT traction inverter employed in TGN39-type metro vehicle.
介绍了TGN39型地铁车辆用DC 1500 V IGBT牵引逆变器的主要参数、主电路和总体结构,阐述了该逆变器的技术特点。
5) IGBT inverter
![点击朗读](/dictall/images/read.gif)
IGBT逆变
1.
Control system design of IGBT inverter type submerged arc welding machine;
![点击朗读](/dictall/images/read.gif)
IGBT逆变埋弧焊机控制系统设计
2.
Suppression technology of electromagnetic disturbance for IGBT inverter welder
![点击朗读](/dictall/images/read.gif)
IGBT逆变焊机电磁骚扰的抑制
3.
The design used 220 V AC,DC rectifier and chopper voltage regulation,through the IGBT inverter for the exchange,finally filtering through the inductor,boost high-frequency transformer to achieve the high voltage output of the high-frequency sine wave.
本设计采用220 V交流输入,经整流成直流后,通过直流斩波调压,再通过IGBT逆变为交流,最后通过电感滤波、高频变压器升压来实现输出为高频高压的正弦波。
补充资料:换流站逆变侧交流系统故障
换流站逆变侧交流系统故障
AC system faults on inverter side of converer station
huanl一uZhonn{b一oneeJ一00!旧xltong guZhong换流站逆变侧交流系统故阵(AC systemfaults on inverter side of eonverter station)直流抽电受端交流系统发生的故障,包括三相短路、两相短路、两相对地短路、单相对地短路以及断线等.在常规的直流物电系统中,逆变器必须在受端交流系统提供的换相电压支持下才能正常工作。交流电网的故障会使逆变站交流母线电压的幅值、相位和波形发生变化,这些变化将可能引起逆变侧控制系统失去同步基准信号、阀触发系统储能不足,或逆变器的换相失败(见换流莽故降).逆变侧交流系统故障对直流系统的形响比整流侧的严重,其形响的程度往往以是否引发逆变器的换相失败或换相失败后是否能自行恢复正常来衡t。 三相对称故瘫,将由于故障地点的远近不同而使换相母线电压的下降程度不同,通常下降至额定电压的70%~60%时,逆变器就可能发生换相失败。由换相电流关系式可推导出三相交流电压下降造成逆变器发生换相失败的极限下降系数,即护万v[eos下。一eos(7。一y。。+600)〕式中。岛为换相电抗;几为直流运行电流,y。为关断角整定值;ym.二为极限关断角;U为故障前交流母线线电压有效值。如果采用低压限流(VDCL)的措施.通常在额定电压的40%时,还可维持直流系统运行。 交流系统不对称故障会使逆变站交流母线各相电压幅值和相位发生不同程度的变化。不对称故障除了降低换相电压外,还引起换相电压过零点的不对称移动,从而又直接影响到换流阀的关断角。通常不对称故障对关断角的影响比对称故障更严重。当逆变侧交流系统发生不对称故障时,逆变器往往会由于关断角变小而发生换相失败。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条