1) Dividing Injection
二次燃油喷射
1.
And last, an novel conception of "Dividing Injection" for port injection engine is put forward.
作者首先对所设计的几种类型的滚流进气道在稳流试验台上进行了系统性的研究，进而设计了三进气道的强滚流进气方案，设计改造普通下置凸轮轴二气门CA1102Q汽油机成为双顶置凸轮轴五气门燃油喷射强滚流稀燃汽油机，并首次对在气道内实施“二次燃油喷射”来改善燃烧进行了实验研究。
2) Two-stage Fuel Injection
两次燃油喷射
3) secondary hot gas injection
燃气二次喷射
1.
The working process of secondary hot gas injection thrust vector control for solid rocket motor is numerically simulated using quasi-one-dimensional unsteady N-S equations.
采用准一维非定常N-S方程对固体火箭发动机燃气二次喷射推力矢量控制过程进行数值仿真,研究燃气引出和燃气二次喷射对发动机燃烧室及喷管内流场的影响。
2.
Gas conduction,secondary hot gas injection as well as their interaction with the main flow of the motor were investigated respectively.
采用基于Favre平均的三维N-S方程,对燃气推力矢量控制发动机全内流场进行了数值仿真,研究了燃气引流、燃气二次喷射及与发动机内主流相互作用等复杂流动。
4) hot gas secondary injection
燃气二次喷射
1.
The unsteady effect of closure process for hot gas secondary injection thrust vector control(HGSITVC) system was studied by computational fluid dynamics(CFD) analysis technique.
采用数值模拟方法对燃气二次喷射推力矢量控制系统关闭过程中非定常效应进行研究。
5) fuel injection
燃油喷射
1.
Simulating the high-pressure common-rail fuel injection system of diesel engines;
柴油机高压共轨式燃油喷射系统的仿真研究
2.
Intelligent update and design of a fuel injection system test device;
一种燃油喷射系统实验台智能化改造与设计
3.
Design and Experimental Research of Fuel Injection and Ignition Control System for Electronically Controlled Gasoline Engine;
电控汽油机燃油喷射及点火控制系统的设计与实验研究
6) Secondary injection
二次喷射
1.
Based on the PW2000 fuel injection pump,by fuel injection pump performance testing and comparing,the influences of delivery valve s opening pressure,diameter of fuel returning hole and seat angle of returning valve on injection pump pressure,nozzle pressure,residual pressure,injection pattern,secondary injection and cavitations were discussed in this paper.
以PW 2000喷油泵为基础,通过喷油泵性能测试对比研究与分析,研究在高喷射压力强化条件下,等压出油阀偶件回油阀开启压力、回油孔直径、回油阀座面角度对喷油泵泵端压力、嘴端压力、残余压力、喷油规律综合性能及燃油液力系统穴蚀、二次喷射的影响规律与程度。
2.
On the base of the PMS type pump, which is produced by Weifu group company and powerful in in-line pumps, under high injection pressure the influences of three kinds of basic delivery valves on the comprehensive performance, such as pump pressure, nozzle pressure, residual pressure, injection rate, secondary injection and cavitation, are investigated.
以无锡威孚公司目前机械直列喷油泵产品中强化程度较高的PMS喷油泵为基础 ,通过试验研究的方法 ,对比测试与分析等压出油阀、阻尼阀、等容出油阀喷油泵性能数据 ,研究 3种基本出油阀偶件在高喷射压力强化条件下 ,对喷油泵泵端压力、嘴端压力、喷油规律与燃油液力系统穴蚀、二次喷射的影响规律与程度。
补充资料：输出反馈(见线性二次型次优控制)
输出反馈(见线性二次型次优控制)
output feedback
3h日c卜口fon以以{输出反馈型次优控制。(output王eedbaek)见线性二次
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条