1) micro trench
微细凹槽
1.
The no-blemish copper deposition in micro trench is the essential problem needing to be resolved in the development of ULSI manufacture.
微细凹槽内无空洞和缝隙缺陷镀铜是集成电路芯片铜布线制造工艺技术发展中需解决的一个关键问题。
2) mini-channel
微细槽道
1.
Experimental and numerical study on the performances of mini-channel heat sinks
微细槽道散热器性能实验和数值研究
3) capillary microgrooves
毛细微槽群
1.
Theoretical analysis of axial dryout point height in vertical rectangular capillary microgrooves;
竖直矩形毛细微槽群轴向干涸高度的理论分析
2.
Dryout characteristics of evaporating liquid in vertical capillary microgrooves heat sink;
竖直毛细微槽群热沉中蒸发液体的干涸特性
3.
Using a wide field stereo-microscope,a high-speed camera and a CCD video camera,liquid dryout behaviors and axial wetting height in vertical rectangular capillary microgrooves were observed and measured under the conditions of pure evaporation and boiling heat transfer.
实验结果表明:竖直矩形毛细微槽群是一种高性能的相变换热强化表面,微槽中液体的蒸发与沸腾对干涸点高度的变化有着复杂的影响,热流密度和相变换热系数沿槽道方向的分布不均匀。
4) groove
[英][ɡru:v] [美][gruv]
凹槽
1.
The Fast Multipole Method for Electromagnetic Scattering of a Groove in a Perfectly Conducting Plane;
无限大导体平面上凹槽散射的快速多极子分析
2.
Fast Calculation of Wide Angle Scattering Fields of a Groove in a Perfectly Conducting Plane Based on Asymptotic Waveform Evaluation Technique;
渐近波形估计应用于无限大导体平面上凹槽散射场宽角度方向性函数的快速获取
3.
BST thick films are fabricated in the grooved silicon substrate by tape casting method.
采用流延法在有凹槽的硅片上制备出钛酸锶钡((Ba,Sr)TiO3)厚膜材料。
5) cavity
[英]['kævəti] [美]['kævətɪ]
凹槽
1.
Numerical study of supersonic turbulence flows on 2-D cavity;
二维凹槽超声速湍流流动数值模拟
2.
Study on cavity flow characteristics of supersonic combustor;
超音速燃烧室凹槽流动特性研究
3.
The large eddy simulation of supersonic cavity flow field
超声速凹槽大涡数值模拟研究
6) notch groove
凹槽
1.
Experimental study on permeability of fresh-old concrete bonding interface with notch groove;
带凹槽的新老混凝土粘结面渗透性能试验研究
2.
Based on the bonding mechanism and permeability of repair interfacial layer between new and old concrete,an idea to significantly increase bonding impermeability by means of chipping notch groove on the old concrete was proposed.
通过带凹槽的老混凝土粘结面与新混凝土粘结的复合圆台柱体试件的渗透性能对比试验研究,分析了凹槽宽度、粗糙度、界面剂等对粘结面渗透性能的影响。
补充资料：凹模壁厚及凹模垫板尺寸
型腔壁部投影面积 壁 厚， 毫 米
F， 厘米2 h1 h2 h3 h4 h5
<5 15~20 30~40 <=10 15~20 30~40
>5~10 20~25 40~50 10~15 20~25 40~55
>10~50 20~30 50~60 15~20 20~30 55~65
>50~100 30~35 60~75 20~25 30~40 65~70
>100~200 35~40 75~85 25~30 40~50 70~75
>200 >40 >85 30~35 50~60 >80
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条